Alpine CDA 105 Cda-105 Owners Manual - Page 20

POWER IC ON: The speakers are driven by the built-in amplifier. SPEAKER RIGHT FRONT Speakers Front right SPEAKER RIGHT REAR SPEAKER LEFT REAR Rear right Rear left SPEAKER LEFT FRONT Front left • No sound is produced by the system when the power output is set to OFF. Turning Mute Mode On/Off (INT MUTE) MUTE ON / MUTE OFF (Initial setting) If a device having the interrupt feature is connected, audio will be automatically muted whenever the interrupt signal is received from the device. Setting the AUX+ SETUP Mode AUX+ ON / AUX+ OFF (Initial Setting) You can input the audio of an external device, (such as a Portable audio player) to the Bluetooth interface connector of this unit. A special Conversion cable (KCE-237B) is necessary to adapt the Bluetooth interface connector as an AUX IN. A portable music device and a Bluetooth INTERFACE (KCE-400BT) cannot be connected to the Bluetooth interface connector at the same time. AUX+ ON: Set to ON when a portable device is connected. If SOURCE/ is pressed and AUX+ is selected, the sound of the portable device is input to the unit. AUX+ OFF: When set to OFF, AUX+ source cannot be selected. You can change the AUX+ NAME display when AUX+ SETUP is set to ON. Press /ENT when AUX+ SETUP is set to ON, and select AUX+ NAME by turning the Rotary encoder, then press /ENT. After that, turn the Rotary encoder to select the desired AUX+ NAME. Setting the AUX+ Level (AUX IN GAIN) LOW (Initial setting) / HIGH After setting to ON in "Setting the AUX+ SETUP Mode", this setting can be carried out. LOW: HIGH: Decreases the external input audio level. Increases the external input audio level. Setting the External Digital Input D-AUX ON / D-AUX OFF (Initial setting) When an ALPINE Ai-NET compatible digital audio processor (PXA-H701) and a DVD player (DVE-5207) not compatible with Ai-NET are connected, set D-AUX to ON to enjoy 5.1-channel surround sound. You can change the D-AUX NAME display when D-AUX is set to ON. Press /ENT when D-AUX is set to ON, and select D-AUX NAME by turning the Rotary encoder, then press /ENT. After that, turn the Rotary encoder to select the desired D-AUX NAME. • Press SOURCE/ , and select the DIGITAL-AUX mode, and adjust the volume, etc. • After input selection is completed, turn the ignition off and back on again. Setting of the optical digital input switch is completed. • Depending on the connected audio processor, DVD player sound may continue to be output, even though the source is changed to another one. If this occurs, set the DVD player's power to OFF. Setting the AUX Mode (V-Link) AUX IN ON / AUX IN OFF (Initial setting) You can input TV/video sound by connecting an optional Ai-NET/RCA Interface cable (KCA-121B) or Versatile Link Terminal (KCA-410C) to this component. You can change the AUX name display when AUX IN is set to ON. Press /ENT when AUX IN is set to ON, and select AUX NAME by turning the Rotary encoder, and then press /ENT. After that, turn the Rotary encoder to select the desired AUX name. If the KCA-410C is connected, it is possible to select two AUX names. • Via KCA-410C, up to 2 external devices with RCA output can be connected. In this case, press SOURCE/ to select AUX mode and then press BAND to select your desired device. Changer Name Setting CHANGER (Initial Setting) / USB / PORTABLE This setting is used when the head unit is connected to the USB Adapter for MP3 (KCA-620M). You can set the name to be displayed on the unit depending on the device to which the USB Adapter for MP3 (KCA-620M) is connected. HD Radio Reception (only when HD Radio Tuner module is connected) HD Radio Station Call Setting (STATION CALL) SHORT (Initial setting) / LONG In the HD Radio mode, the number of display characters for the HD Radio station name can be selected. SHORT: LONG: 7 characters (FM) 4 characters (AM) 56 characters Digital Seek ON/OFF Setting DIG SEEK ON / DIG SEEK OFF (Initial Setting) ON: OFF: SEEK UP/DOWN is used only for Digital Radio Station. SEEK UP/DOWN is used for all Radio Stations. 18-EN