Apple M8493 Setup Guide - Page 65

When you replace the carrier and reconnect the drive cables

Get Apple M8493 - G4 PowerMac 10.4 Tiger Opeation System PDF manuals and user guides
UPC - 718103028325
View all Apple M8493 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Note : The tinted screws in the previous illustration indicate the four low-profile screws that came in the computer's accessory kit. The untinted screws in the following illustration show the screws that came with the new drive. Attach additional SCSI drives (1" or 1.6" high) to the two flat drive carriers by screwing them into position from the bottom. Position the hard disk drive on the drive carrier so that the ribbon cable connector and the power cord connector are accessible. Screw the drive into position with the four screws supplied with the drive. When you replace the carrier and reconnect the drive cables If your computer came with a SCSI hard disk drive installed in drive position 1, and you are installing a SCSI hard disk drive in drive position 2 or 3, put the ribbon cable on top of the drives. You can tape the ribbon cable to the tops of the drives with double-stick foam tape to make the cable lie flat. Make sure all of the power cord and ribbon cable connectors are firmly attached to all of the drives and to the PCI SCSI card. SCSI terminator PCI SCSI card The ribbon cable may attach to a different position on the PCI SCSI card, depending on which card you have. Working Inside Your Computer 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Working Inside Your Computer
65
Note :
The tinted screws in the previous illustration indicate the four low-profile screws that
came in the computer’s accessory kit. The untinted screws in the following illustration show
the screws that came with the new drive.
When you replace the carrier and reconnect the drive cables
Attach additional SCSI drives (1" or 1.6" high) to the two flat drive
carriers by screwing them into position from the bottom.
Position the hard disk drive
on the drive carrier so that
the ribbon cable connector
and the power cord connector
are accessible. Screw the drive
into position with the four screws
supplied with the drive.
If your computer came with a SCSI hard disk drive installed in
drive position 1, and you are installing a SCSI hard disk drive
in drive position 2 or 3, put the ribbon cable on top of the drives.
You can tape the ribbon cable to the tops of the drives with
double-stick foam tape to make the cable lie flat.
SCSI terminator
PCI SCSI card
The ribbon cable may attach to a different position on
the PCI SCSI card, depending on which card you have.
Make sure all of the power
cord and ribbon cable
connectors are firmly attached
to all of the drives and to the
PCI SCSI card.