Asus Terminator A7VT Terminator A7VT User Manual - Page 75

Primary IDE Master [Auto], Access Mode [Auto], PIO Mode [Auto]

Get Asus Terminator A7VT PDF manuals and user guides View all Asus Terminator A7VT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

5.3.6 Primary and Secondary Master/Slave IDE Primary Master Primary IDE Master Access Mode Capacity Cylinder Head Sector PIO Mode UDMA Mode Transfer Mode [Auto] [Auto] 0 MB 0 0 0 [Auto] [Auto] None Select Menu Item Specific Help Press [Enter] to select. Primary IDE Master [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu. If automatic detection fails, this may be because the hard disk drive is too old or too new. If the hard disk was already formatted on an older system, Setup may detect incorrect parameters. In these cases, select [Manual] to manually enter the IDE hard disk drive parameters. Refer to the next section for details. Before attempting to configure a hard disk drive, make sure you have the correct configuration information supplied by the drive manufacturer. Incorrect settings may cause the system to fail to recognize the installed hard disk. Access Mode [Auto] This item allows the user to select the sector addressing mode. Configuration options: [CHS] [LBA] [Large] [Auto] PIO Mode [Auto] This option lets you set a PIO (Programmed Input/Output) mode for the IDE device. Modes 0 through 4 provide successive increase in performance. Configuration options: [Auto] [Mode 0] [Mode 1] [Mode 2] [Mode 3] [Mode 4] ASUS Terminator 1 A7VT barebone system 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
ASUS Terminator 1 A7VT barebone system
75
5.3.6
Primary and Secondary Master/Slave
Primary IDE Master [Auto]
Select [Auto] to automatically detect an IDE hard disk drive. If automatic
detection is successful, Setup automatically fills in the correct values for
the remaining fields on this sub-menu. If automatic detection fails, this may
be because the hard disk drive is too old or too new. If the hard disk was
already formatted on an older system, Setup may detect incorrect
parameters. In these cases, select [Manual] to manually enter the IDE
hard disk drive parameters. Refer to the next section for details.
Before attempting to configure a hard disk drive, make sure you have the
correct configuration information supplied by the drive manufacturer.
Incorrect settings may cause the system to fail to recognize the installed
hard disk.
Primary IDE Master
[Auto]
Access Mode
[Auto]
Capacity
0 MB
Cylinder
0
Head
0
Sector
0
PIO Mode
[Auto]
UDMA Mode
[Auto]
Transfer Mode
None
Select Menu
Item Specific Help
Press [Enter] to
select.
IDE Primary Master
Access Mode [Auto]
This item allows the user to select the sector addressing mode.
Configuration options: [CHS] [LBA] [Large] [Auto]
PIO Mode [Auto]
This option lets you set a PIO (Programmed Input/Output) mode for the
IDE device. Modes 0 through 4 provide successive increase in
performance. Configuration options: [Auto] [Mode 0] [Mode 1] [Mode 2]
[Mode 3] [Mode 4]