Bosch SHP78CM2N Installation Instructions - Page 7

Installation Preparation, Installation Procedure

Get Bosch SHP78CM2N PDF manuals and user guides View all Bosch SHP78CM2N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

If the dishwasher is to be installed in a corner, ensure that there is adequate clearance to open the door as shown. Installation Preparation en-us 2. Pull the drain hose out of the packaging base as shown. Installation Preparation 3 Installation Preparation Installation Preparation After locating the proper place for your dishwasher, create an opening to allow for water, drain and electrical lines on the appropriate side. 1. Cut a hole within the 7 x 2.5" area shown. 3. Set the toe panel aside for later use. 4. Remove the hose clip at the back of the dishwasher. 2 ½" (6.3 cm) 7" (17.8 cm) ø 2 ½" (6.3 cm) or It can be used later to hold the drain hose inside your cabinet. If the opening is made through wood, sand it smooth with coarse sandpaper. If the opening is made through metal, use the Edge Protector with Power Cord clips Kit SMZEPCC1UC. Installation Procedure 4 Installation Procedure Installation Procedure Follow these instructions to install the dishwasher. 4.1 Attach Water Inlet Hose NOTICE: Avoid cross-threading ▶ Cross-threading will cause leaks. Teflon tape ▶ Do not use Teflon tape; it could cause leaks and damage floors or cabinetry. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Installation Preparation
en-us
7
If the dishwasher is to be installed in a corner, ensure that
there is adequate clearance to open the door as shown.
3
Installation Preparation
After locating the proper place for your dishwasher, create
an opening to allow for water, drain and electrical lines on
the appropriate side.
1.
Cut a hole within the 7 x 2.5" area shown.
7"
(17.8 cm)
2 ½"
(6.3 cm)
ø 2 ½"
(6.3 cm)
or
If the opening is made through wood, sand it smooth
with coarse sandpaper.
If the opening is made through metal, use the Edge
Protector with Power Cord clips Kit SMZEPCC1UC.
2.
Pull the drain hose out of the packaging base as shown.
3.
Set the toe panel aside for later use.
4.
Remove the hose clip at the back of the dishwasher.
It can be used later to hold the drain hose inside your
cabinet.
4
Installation Procedure
Follow these instructions to install the dishwasher.
4.1
Attach Water Inlet Hose
NOTICE:
Avoid cross-threading
▶
Cross-threading will cause leaks.
Teflon tape
▶
Do not use Teflon tape; it could cause leaks and
damage floors or cabinetry.