Brother International CP60X Operation Manual - Page 22

Zipper insertion

Get Brother International CP60X PDF manuals and user guides View all Brother International CP60X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

CAUTION • When sewing, be sure that the needle does not touch the button, otherwise the needle may bend or break. 9 Sew about 10 stitches at a slow speed. Set the sewing speed controller to the left (so that the speed will be slow). 3 Baste the fabric from the zipper opening to the edge of the fabric. a b 1 Basting stitching 2 Wrong side of fabric 4 Press open the seam allowance from the wrong side of the fabric. 1 1 Wrong side of fabric 10 Use scissors to cut the upper thread and the bobbin thread at the beginning of the stitching. Pull the upper thread at the end of the stitching to the wrong side of the fabric, and then tie it with the bobbin thread. 11 When you are finished attaching the button, slide the feed dog position switch, to and turn the handwheel to raise the feed dogs. Zipper insertion n Inserting a centered zipper Stitching is sewn on both pieces of fabric butted against each other. 1 Right side of fabric 2 Stitching b 3 End of zipper opening a c 1 Attach zigzag foot "J". 2 Sew straight stitches up to the zipper opening. With the right sides of the fabric facing each other, sew reverse stitches after reaching the zipper opening. 1 Reverse stitches 2 End of zipper opening a b 22 5 Align the seam with the center of the zipper, and then baste the zipper in place to the seam allowance. b 1 Wrong side of fabric 2 Basting stitching 3 Zipper a c 6 Remove about 5 cm (2 inches) from the end of the basting on the outside. b d c a 1 Wrong side of fabric 2 Zipper basting 3 Outside basting 4 5 cm (2 inches) 7 Attach the presser foot holder to the right pin of zipper foot "I". I Pin on the right side Needle drop point 8 Select the straight stitch ( middle (center) needle position). * Check the stitch number on the machine's body, and set the machine for that stitch. CAUTION • When using zipper foot "I", be sure to select the straight stitch (middle (center) needle position), and slowly turn the handwheel toward you (counterclockwise) to check that the needle does not touch the presser foot. If a different stitch is selected or the needle hits the presser foot, the needle may bend or break.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
22
CAUTION
• When sewing, be sure that the needle does
not touch the button, otherwise the needle
may bend or break�
9
Sew about 10 stitches at a slow speed�
Set the sewing speed controller to the left (so that
the speed will be slow)�
10
Use scissors to cut the upper thread and the
bobbin thread at the beginning of the stitching�
Pull the upper thread at the end of the stitching to
the wrong side of the fabric, and then tie it with
the bobbin thread�
11
When you are finished attaching the button,
slide the feed dog position switch, to
and
turn the handwheel to raise the feed dogs�
Zipper insertion
n
Inserting a centered zipper
Stitching is sewn on both pieces of fabric butted
against each other�
a
b
c
1
Right side of fabric
2
Stitching
3
End of zipper opening
1
Attach zigzag foot “J”�
2
Sew straight stitches up to the zipper opening�
With the right sides of the fabric facing each
other, sew reverse stitches after reaching the
zipper opening�
a
b
1
Reverse stitches
2
End of zipper opening
3
Baste the fabric from the zipper opening to the
edge of the fabric�
a
b
1
Basting stitching
2
Wrong side of fabric
4
Press open the seam allowance from the wrong
side of the fabric�
1
Wrong side of fabric
1
5
Align the seam with the center of the zipper,
and then baste the zipper in place to the seam
allowance�
1
Wrong side of fabric
2
Basting stitching
3
Zipper
a
b
c
6
Remove about 5 cm (2 inches) from the end of
the basting on the outside�
1
Wrong side of fabric
2
Zipper basting
3
Outside basting
4
5 cm (2 inches)
d
a
b
c
7
Attach the presser foot holder to the right pin
of zipper foot “I”�
I
Pin on the right side
Needle drop point
8
Select the straight stitch (
middle (center)
needle position)�
*
Check the stitch number on the machine’s body,
and set the machine for that stitch�
CAUTION
• When using zipper foot “I”, be sure to select
the straight stitch (middle (center) needle
position), and slowly turn the handwheel
toward you (counterclockwise) to check that
the needle does not touch the presser foot�
If a different stitch is selected or the needle
hits the presser foot, the needle may bend or
break�