Brother International VX-940 Users Manual - English - Page 15

illustrated

Get Brother International VX-940 PDF manuals and user guides View all Brother International VX-940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Upper (Needle) Thread LIJ U 0_11 I 1. Thread guide (rear) Spool pin Thread guide (front) 2. Thread tension dial Thread check spring 3. 4. 5. Thread $ take-up lever Before threading, raise presser foot and turn the balance wheel toward you and raise thread take-up lever to its highest position. Then raise spool pin and place thread spool on the pin. 1. Pass thread through the both of thread guides from rear to front 2. Bring thread down and up through upper thread tension dial from right to left so that the thread picks up the thread check spring. With holding thread as illustrated, pull up thread and deliver into the eye in tension disc. 3. Thread take-up lever by guiding thread to back of lever and around to your left. Bring thread through slit by pulling it toward you and into eyelet. 4. Bring down and pass through the thread guard and guides. 5. Thread needle from front to back and draw the thread out about 2 inches (5 cm). NOTE: IF THE THREADING ORDER IS NOT CORRECT, THREAD BREAKAGE, STITCH SKIPPING AND WRINKLING OF FABRIC WILL OCCUR. -13-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
Upper
(Needle)
Thread
LIJ
U
0_11
I
1.
Thread
guide
(rear)
Spool
pin
Thread
guide
(front)
2.
Thread
check
spring
Thread
tension
dial
3.
Thread
take-up
lever
$
4.
5.
Before
threading,
raise
presser
foot
and
turn
the
balance
wheel
toward
you
and
raise
thread
take-up
lever
to
its
highest
position.
Then
raise
spool
pin
and
place
thread
spool
on
the
pin.
1.
Pass
thread
through
the
both
of
thread
guides
from
rear
to
front
2.
Bring
thread
down
and
up
through
upper
thread
tension
dial
from
right
to
left
so
that
the
thread
picks
up
the
thread
check
spring.
With
holding
thread
as
illustrated,
pull
up
thread
and
deliver
into
the
eye
in
tension
disc.
3.
Thread
take-up
lever
by
guiding
thread
to
back
of
lever
and
around
to
your
left.
Bring
thread
through
slit
by
pulling
it
toward
you
and
into
eyelet.
4.
Bring
down
and
pass
through
the
thread
guard
and
guides.
5.
Thread
needle
from
front
to
back
and
draw
the
thread
out
about
2
inches
(5
cm).
NOTE:
IF
THE
THREADING
ORDER
IS
NOT
CORRECT,
THREAD
BREAKAGE,
STITCH
SKIPPING
AND
WRINKLING
OF
FABRIC
WILL
OCCUR.
-13-