Brother International VX-940 Users Manual - English - Page 17

thread should

Get Brother International VX-940 PDF manuals and user guides View all Brother International VX-940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

HOW TO REMOVE AND INSERT BOBBIN CASE TO REMOVE BOBBIN CASE 1. Raise needle to its highest position. • 2. Open the shuttle cover by turning it down. 3. Pull 'and open the latch of bobbin case. 4. Pul l out bobbin case from the shuttle. TO INSERT BOBBIN CASE 1. Raise needle to its highest position. 2. Holding bobbin case latch with metal finger of case pointing up, fit it into the notch at the top of shuttle race. 3. Push case back fully 'making sure the case is in the proper position and release the l'atch. NOTE: (A) 4 inches (10 cm) of thread should be drawn out and left out of case. (B) Latch of bobbin case should be open fully to prevent bobbin coming out of case. (C) If bobbin case is not placed back in machine properly it will come out from the shuttle immediately . after starting to sew. HOW TO THREAD BOBBIN CASE ..... Tension spring , (3 (2, , .. 1. Unwind about 4 incheS (10 cm) of thread from the bobbin. Insert wound bobbin into bobbin case. 2. Pul l trailing thread into the slot of case. 3. Pull thread to the left under tension spring until thread enters into delivery eye. - 15 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
HOW
TO
REMOVE
AND
INSERT
BOBBIN
CASE
TO
REMOVE
BOBBIN
CASE
HOW
TO
THREAD
BOBBIN
CASE
1.
Raise
needle
to
its
highest
position.
•
2.
Open
the
shuttle
cover
by
turning
it
down.
3.
Pull
'and
open
the
latch
of
bobbin
case.
4.
Pul
l
out
bobbin
case
from
the
shuttle.
TO
INSERT
BOBBIN
CASE
1.
Raise
needle
to
its
highest
position.
2.
Holding
bobbin
case
latch
with
metal
finger
of
case
pointing
up,
fit
it
into
the
notch
at
the
top
of
shuttle
race.
3.
Push
case
back
fully
'making
sure
the
case
is
in
the
proper
position
and
release
the
l'atch.
NOTE:
(A)
4
inches
(10
cm)
of
thread should
be
drawn
out
and
left
out
of
case.
(B)
Latch
of
bobbin
case
should
be
open
ful
ly
to
prevent
bobbin
coming
out
of
case.
(C)
If
bobbin
case
is
not
placed
back
in
machine
properly
it
wil
l
come
out
from
the
shuttle
immediately
.
after
starting
to
sew.
.....
Tension
spring
,
(3
(2,
,
..
1.
Unwind
about
4
incheS
(10
2.
Pul
l
trailing
thread
into
3.
Pull
thread
to
the
left
cm)
of
thread
from
the
the
slot
of
case.
under
tension
spring
until
bobbin.
Insert
wound
thread
enters
into
delivery
bobbin
into
bobbin
case.
eye.
—
15
-