Brother International VX-940 Users Manual - English - Page 39

Monogramming, Embroidering, Using, Embroidery

Get Brother International VX-940 PDF manuals and user guides View all Brother International VX-940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Monogramming and Embroidering, Using Embroidery Hoop PATTERN SELECTOR STITCH LENGTH STITCH WIDTH NEEDLE POSITION SELECTOR PRESSER FOOT NEEDLE OTHERS PRESSURE ADJUSTER : 2 Set at any position. 0^'5 : M : Removed Single : Darning plate Up (Free) PREPARATION FOR MONOGRAMMING AND EMBROIDERING 1 Place darning plate on needle plate. 2. Set your sewing machine as per side instructions. 3. Draw lettering (for monogramming) or design (for embroidering) on the right side of the material. 4. Stretch work between embroidery hoops as firmly as possible. 5. Place the work under the needle and lower presser bar. 6. Pull lower thread up through the work as starting position by turning balance wheel and make a few holding stitches. 7. Hold the hoop with thumb and forefingers of both hands while pressing the material with middle and third fingers and supporting the outside of hoop with smaller finger. C;P; S. eje tet ce MONOGRAMMING 1 . Sew, moving hoop slowly along the lettering at an even rate of speed. 2. Secure with a few straight stitches. (NOTE: These instructions also apply to embroidering) EMBROIDERING ) 1. Stitch outline of design by moving embroidery hoop accordingly. 2. Fill in design stitch from outline of design to inside and from inside to edge of outline alternately until design is completely fil led in. Keep stitching close together. NOTE: A long stitch is made by moving embroidery hoop rapidly and a short stitch is made by moving it slowly. - 37 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
Monogramming
and
Embroidering,
Using
Embroidery
Hoop
PATTERN
SELECTOR
STITCH
LENGTH
STITCH
WIDTH
NEEDLE
POSITION
SELECTOR
PRESSER
FOOT
NEEDLE
OTHERS
PRESSURE
ADJUSTER
:
2
Set
at
any
position.
0^'5
:
M
:
Removed
Single
:
Darning
plate
Up
(Free)
PREPARATION
FOR
MONOGRAMMING
AND
EMBROIDERING
1
Place
darning
plate
on
needle
plate.
2.
Set
your
sewing
machine
as
per
side
instructions.
3.
Draw
lettering
(for
monogramming)
or
design
(for
embroidering)
on
the
right
side
of
the
material.
4.
Stretch
work
between
embroidery
hoops
as
firmly
as
possible.
5.
Place
the
work
under
the
needle
and
lower
presser
bar.
6.
Pull
lower
thread
up
through
the
work
as
starting
position
by
turning
balance
wheel
and
make
a
few
holding
stitches.
7.
Hold
the
hoop
with
thumb
and
forefingers
of
both
hands
while
pressing
the
material
with
middle
and
third
fingers
and
supporting
the
outside
of
hoop
with
smaller
finger.
C;;
P
S.
eje
tet
ce
)
MONOGRAMMING
1
.
Sew,
moving
hoop
slowly
along
the
lettering
at
an
even
rate
of
speed.
2.
Secure
with
a
few
straight
stitches.
(NOTE:
These
instructions
also
apply
to
embroidering)
EMBROIDERING
1.
Stitch
outl
ine
of
design
by
moving
embroidery
hoop
accordingly.
2.
Fill
in
design
stitch
from
outline
of
design
to
inside
and
from
inside
to
edge
of
outline
alternately
until
design
is
completely
fi
l
led
in.
Keep
stitching
close
together.
NOTE:
A
long
stitch
is
made
by
moving
embroidery
hoop
rapidly
and
a
short
stitch
is
made
by
moving
it
slowly.
—
37
—