Home » Cisco Manuals » Wireless » Cisco WRT54G » Manual Viewer

Cisco WRT54G User Manual - Page 22

Optional Settings, Router IP, Network Address Server Settings DHCP, Network Setup - manual

Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Wireless-G Broadband Router When you are finished, click the Save Settings button. Then click the Status tab, and click the Connect button to start the connection. Optional Settings Some of these settings may be required by your ISP. Verify with your ISP before making any changes. Router Name. In this field, you can type a name of up to 39 characters to represent the Router. Host Name/Domain Name. These fields allow you to supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work. MTU. MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission. The default setting, Manual, allows you to enter the largest packet size that will be transmitted. The recommended size, entered in the Size field, is 1492. You should leave this value in the 1200 to 1500 range. To have the Router select the best MTU for your Internet connection, select Auto. Network Setup The Network Setup section changes the settings on the network connected to the Router's Ethernet ports. Wireless Setup is performed through the Wireless tab. Router IP This presents both the Router's IP Address and Subnet Mask as seen by your network. Network Address Server Settings (DHCP) The settings allow you to configure the Router's Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the Router's DHCP server option, you must configure all of your network PCs to connect to a DHCP server (the Router), and make sure there is no other DHCP server on your network. DHCP Server. DHCP is enabled by factory default. If you already have a DHCP server on your network, or you don't want a DHCP server, then click the Disable radio button (no other DHCP features will be available). Figure 5-9: Optional Settings Figure 5-10: Router IP Figure 5-11: Network Address Server Settings Chapter 5: Configuring the Wireless-G Broadband Router 16 The Setup Tab - Basic Setup

Section	Page
English, User Guide	1
Copyright and Trademarks	2
Table of Contents	3
List of Figures	5
Chapter 1: Introduction	7
Chapter 2: Planning Your Wireless Network	10
Chapter 3: Getting to Know the Wireless-G Broadband Router	12
Chapter 4: Connecting the Wireless-G Broadband Router	14
Chapter 5: Configuring the Wireless-G Broadband Router	18
Appendix A: Troubleshooting	46
Appendix B: Wireless Security	61
Appendix C: Upgrading Firmware	64
Appendix D: Windows Help	65
Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter	66
Appendix F: Glossary	68
Appendix G: Specifications	73
Appendix H: Warranty Information	75
Appendix I: Regulatory Information	76
Appendix J: Contact Information	87
Dansk, Brugervejledning	89
Copyright og varemærker	90
Indhold	91
Liste over figurer	93
Kapitel 1: Introduktion	95
Kapitel 2: Planlægning af dit trådløse netværk	98
Kapitel 3: Lær den Trådløse-G-bredbåndsrouter at kende	100
Kapitel 4: Tilslutning af den Trådløse-G- bredbåndsrouter	102
Kapitel 5: Konfigurering af den Trådløse-G- bredbåndsrouter	106
Appendiks A: Fejlfinding	134
Appendiks B: Trådløs sikkerhed	151
Appendiks C: Opgradering af firmware	154
Appendiks D: Windows Hjælp	155
Appendiks E: Sådan finder du MAC-adressen og IP-adressen på dit Ethernet-kort	156
Appendiks F: Ordliste	158
Appendiks G: Specifikationer	163
Appendiks H: Garantioplysninger	165
Appendiks I: Lovmæssige oplysninger	166
Appendiks J: Kontaktoplysninger	177
Deutsch, Benutzerhandbuch	179
Copyright und Marken	180
Inhalt	181
Liste der Abbildungen	183
Kapitel 1: Einführung	186
Kapitel 2: Planen des Wireless-Netzwerks	189
Kapitel 3: Kennenlernen des Wireless-G Broadband- Routers	191
Kapitel 4: Anschließen des Wireless-G Broadband-Routers	193
Kapitel 5: Konfigurieren des Wireless-G Broadband- Routers mit SRX400	197
Anhang A: Fehlerbehebung	225
Anhang B: Wireless-Sicherheit	240
Anhang C: Aktualisieren der Firmware	243
Anhang D: Windows-Hilfe	244
Anhang E: Ermitteln der MAC-Adresse und der IP-Adresse des Ethernet-Adapters	245
Anhang F: Glossar	247
Anhang G: Spezifikationen	252
Anhang H: Garantieinformationen	254
Anhang I: Zulassungsinformationen	255
Anhang J: Kontaktinformationen	266
Español, Guía del usuario	268
Copyright y marcas comerciales	269
Contenido	270
Lista de figuras	272
Capítulo 1: Introducción	275
Capítulo 2: Planificación de la red inalámbrica	278
Capítulo 3: Familiarización con el ruteador de banda ancha Wireless-G	280
Capítulo 4: Conexión del ruteador de banda ancha Wireless-G	282
Capítulo 5: Configuración del ruteador de banda ancha Wireless-G	286
Apéndice A: Resolución de problemas	314
Apéndice B: Seguridad inalámbrica	330
Apéndice C: Actualización del firmware	333
Apéndice D: Ayuda de Windows	334
Apéndice E: Búsqueda de la dirección MAC e IP del adaptador Ethernet	335
Apéndice F: Glosario	337
Apéndice G: Especificaciones	342
Apéndice H: Información de garantía	344
Apéndice I: Información sobre normativa	345
Apéndice J: Información de contacto	356
Français, Guide de l’utilisateur	358
Copyright et marques commerciales	359
Table des matières	360
Liste des figures	362
Chapitre 1 : Introduction	365
Chapitre 2 : Planification de votre réseau sans fil	368
Chapitre 3 : Présentation du routeur haut débit sans fil - G	370
Chapitre 4 : Connexion du routeur haut débit sans fil - G	373
Chapitre 5 : Configuration du routeur haut débit sans fil - G	378
Annexe A : Dépannage	409
Annexe B : Sécurité sans fil	427
Annexe C : Mise à niveau du micrologiciel	430
Annexe D : Aide - Windows	431
Annexe E : Recherche des adresses MAC et IP de votre adaptateur Ethernet	432
Annexe F : Glossaire	434
Annexe G : Spécifications	439
Annexe H : Informations de garantie	441
Annexe I : Réglementation	442
Annexe J : Contacts	453
Italiano, Guida per l'utente	455
Copyright e marchi	456
Sommario	457
Elenco delle illustrazioni	459
Capitolo 1: Introduzione	461
Capitolo 2: Pianificazione della rete wireless	464
Capitolo 3: Introduzione al router a banda larga Wireless-G	466
Capitolo 4: Collegamento del router a banda larga Wireless-G	468
Capitolo 5: Configurazione del router a banda larga Wireless-G	473
Appendice A: Risoluzione dei problemi	501
Appendice B: Protezione wireless	518
Appendice C: Aggiornamento del firmware	521
Appendice D: Guida in linea di Windows	522
Appendice E: Ricerca degli indirizzi MAC e IP per l'adattatore Ethernet	523
Appendice F: Glossario	525
Appendice G: Specifiche tecniche	530
Appendice H: Informazioni sulla garanzia	532
Appendice I: Informazioni sulle normative	533
Appendice J: Informazioni sui Contatti	544
Nederlands, Gebruikershandleiding	546
Copyright en handelsmerken	547
Inhoudsopgave	548
Lijst met afbeeldingen	550
Hoofdstuk 1: Inleiding	552
Hoofdstuk 2: Het plannen van uw draadloze netwerk	555
Hoofdstuk 3: Bekend raken met de Wireless-G- breedbandrouter	557
Hoofdstuk 4: Het aansluiten van de Wireless-G- breedbandrouter	559
Hoofdstuk 5: De Wireless-G-breedbandrouter configureren	563
Bijlage A: Probleemoplossing	593
Bijlage B: WLAN-beveiliging	610
Bijlage C: Het upgraden van de firmware	613
Bijlage D: Windows Help	614
Bijlage E: Het achterhalen van het MAC- en IP-adres voor uw Ethernet-adapter	615
Bijlage F: Verklarende woordenlijst	617
Bijlage G: Specificaties	622
Bijlage H: Informatie over garantie	624
Bijlage I: Informatie over regelgeving	625
Bijlage J: Contactgegevens	636
Portuguese, Manual do Utilizador	638
Direitos de autor e marcas comerciais	639
Índice	640
Lista de Figuras	642
Capítulo 1: Introdução	645
Capítulo 2: Planear a rede sem fios	648
Capítulo 3: Conhecer o Router sem fios G de banda larga	650
Capítulo 4: Ligar o Router sem fios G de banda larga	652
Capítulo 5: Configurar o Router sem fios G de banda larga	656
Apêndice A: Resolução de problemas	684
Apêndice B: Segurança sem fios	701
Apêndice C: Actualizar o firmware	704
Apêndice D: Ajuda do Windows	705
Apêndice E: Localizar o endereço MAC e o endereço IP da placa Ethernet	706
Apêndice F: Glossário	708
Apêndice G: Especificações	713
Apêndice H: Informações sobre a garantia	715
Apêndice I: Informações de regulamentação	716
Apêndice J: Informações de contacto	727
Svenska, Användarhandbok	729
Copyright och varumärken	730
Innehåll	731
Figurlista	733
Kapitel 1: Inledning	735
Kapitel 2: Planera ditt trådlösa nätverk	738
Kapitel 3: Börja lära känna Wireless-G Bredbandsrouter	740
Kapitel 4: Ansluta Wireless-G Bredbandsrouter	742
Kapitel 5: Konfigurera Wireless-G Bredbandsrouter	746
Bilaga A: Felsökning	774
Bilaga B: Trådlös säkerhet	791
Bilaga C: Uppgradera fast programvara	794
Bilaga D: Windows-hjälpen	795
Bilaga E: Hitta MAC-adress och IP-adress för Ethernet- adaptern	796
Bilaga F: Ordlista	798
Bilaga G: Specifikationer	803
Bilaga H: Garantiinformation	805
Bilaga I: Information om regler	806

Match case Limit results 1 per page

Chapter 5: Configuring the Wireless-G Broadband Router

The Setup Tab - Basic Setup

Wireless-G Broadband Router

When you are finished, click the

Save Settings

button. Then click the

Status

tab, and click the

Connect

button to start the connection.

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Router Name

. In this field, you can type a name of up to 39 characters to represent the Router.

Host Name/Domain Name

. These fields allow you to supply a host and domain name for the Router. Some ISPs,

usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your

broadband Internet service has been configured with a host and domain name. In most cases, leaving these

fields blank will work.

MTU

. MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet

transmission. The default setting,

Manual

, allows you to enter the largest packet size that will be transmitted.

The recommended size, entered in the

Size

field, is 1492. You should leave this value in the 1200 to 1500 range.

To have the Router select the best MTU for your Internet connection, select

Auto

Network Setup

The Network Setup section changes the settings on the network connected to the Router’s Ethernet ports.

Wireless Setup is performed through the Wireless tab.

Router IP

This presents both the Router’s IP Address and Subnet Mask as seen by your network.

Network Address Server Settings (DHCP)

The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The

Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to

each computer on your network. If you choose to enable the Router’s DHCP server option, you must configure all

of your network PCs to connect to a DHCP server (the Router), and make sure there is no other DHCP server on

your network.

DHCP Server

. DHCP is enabled by factory default. If you already have a DHCP server on your network, or you

don’t want a DHCP server, then click the

Disable

radio button (no other DHCP features will be available).

Figure 5-11: Network Address Server Settings

Figure 5-10: Router IP

Figure 5-9: Optional Settings