Compaq 2510p HP Compaq 2510p Notebook PC - Maintenance and Service Guide - Page 82
Remove the three Torx T8M2.5×7.0 screws, until it rests at an
 |
View all Compaq 2510p manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 82 highlights
6. Disconnect the front LED board cable (1) and the speaker cable (2) from the system board. 7. Remove the three Torx T8M2.5×7.0 screws (1) and the two Phillips PM2.0×10.0 screws (2) that secure the system board to the base enclosure. 8. Use the optical drive connector (1) to lift the left side of the system board (2) until it rests at an angle. 9. Remove the system board (3) by sliding it away from the base enclosure at an angle. 72 Chapter 4 Removal and replacement procedures
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77 -
78 -
79 -
80 -
81 -
82 -
83 -
84 -
85 -
86 -
87 -
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
 |
 |
6.
Disconnect the front LED board cable
(1)
and the speaker cable
(2)
from the system board.
7.
Remove the three Torx T8M2.5×7.0 screws
(1)
and the two Phillips PM2.0×10.0 screws
(2)
that
secure the system board to the base enclosure.
8.
Use the optical drive connector
(1)
to lift the left side of the system board
(2)
until it rests at an
angle.
9.
Remove the system board
(3)
by sliding it away from the base enclosure at an angle.
72
Chapter 4
Removal and replacement procedures