Compaq ProLiant 7000 SMART-2DH Array Controller Reference Guide - Page 181

SMART-2DH Array, Controller Installation Guide, Slot x Drive Array - ProLiant Drive Storage

Get Compaq ProLiant 7000 PDF manuals and user guides View all Compaq ProLiant 7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 181 highlights

H-6 POST Error Messages POST Error Messages continued 1777 Slot x Drive Array - ProLiant Drive Storage System Problem Detected (followed by one or more of the following): SCSI Port (y): Cooling Fan Malfunction Detected SCSI Port (y): Overheated Condition Detected SCSI Port (y): Side-Panel must be Closed to Prevent Overheating SCSI Port (y): Redundant Power Supply Malfunction Detected SCSI Port (y): Wide SCSI Transfer Failed SCSI Port (y): Interrupt Signal Inoperative (RESUME = F1 KEY) Check cooling fan operation by placing hand over fan. Check internal plenum cooling fan in tower servers or storage systems. If fan is not operating, check for obstructions and check all internal connectors. Replace unit side panel if removed. If the ProLiant Storage System power LED is amber instead of green, this indicates a redundant power supply failure. Check SCSI cables. Note that port 1 refers to the "internal" SCSI bus, and port 2 refers to the "external" SCSI bus. If the message indicates to check SCSI cables, verify your cabling using the diagrams in the SMART-2DH Array Controller Installation Guide. If the routing is correct, replace cables on the specified port until the POST message is eliminated. 1778 Slot x Drive Array resuming Automatic Data Recovery process. No action required. This message appears when a controller resets or power cycle occurs while Automatic Data Recovery is in progress. 1779 Slot x Drive Array - Replacement drive(s) detected OR previously failed drive(s) now appear to be operational: Port (y): SCSI ID (x): Restore data from backup if replacement drive x has been installed. If this message appears and drive x (identified by its SCSI ID) has not been replaced, this indicates an intermittent drive failure. This message also appears once immediately following drive replacement before data is restored from backup. 1783 Slot x Drive Array Controller Failure. If this message appears immediately following a ROM installation, the ROM is defective or not installed properly. Check that the controller is firmly inserted in its slot. Try upgrading the System ROMs. Otherwise, replace the SMART2DH Controller. 1784 Slot x Drive Array Drive Failure. The following SCSI drive(s) should be replaced: SCSI Port (y) SCSI ID (x) Check for loose cables. Replace defective drive x and/or cable(s). Writer: Pamela King Project: SMART-2DH Array Controller Reference Guide Comments: 295469-002 File Name: O-APPH.DOC Last Saved On: 2/27/98 12:10 PM COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
H-6
POST Error Messages
Writer: Pamela King
Project: SMART-2DH Array Controller Reference Guide
Comments: 295469-002
File Name: O-APPH.DOC
Last Saved On: 2/27/98 12:10 PM
COMPAQ CONFIDENTIAL - NEED TO KNOW REQUIRED
POST Error Messages
continued
1777
Slot x Drive Array - ProLiant Drive Storage
System Problem Detected (followed by one
or more of the following):
SCSI Port (y): Cooling Fan Malfunction
Detected
SCSI Port (y): Overheated Condition
Detected
SCSI Port (y): Side-Panel must be Closed
to Prevent Overheating
SCSI Port (y): Redundant Power Supply
Malfunction Detected
SCSI Port (y): Wide SCSI Transfer Failed
SCSI Port (y): Interrupt Signal Inoperative
(RESUME =
F1
KEY)
Check cooling fan operation by placing hand
over fan. Check internal plenum cooling fan in
tower servers or storage systems. If fan is not
operating, check for obstructions and check all
internal connectors. Replace unit side panel if
removed.
If the ProLiant Storage System power LED is
amber instead of green, this indicates a
redundant power supply failure.
Check SCSI cables. Note that port 1 refers to
the “internal” SCSI bus, and port 2 refers to the
“external” SCSI bus. If the message indicates
to check SCSI cables, verify your cabling using
the diagrams in the
SMART-2DH Array
Controller Installation Guide
. If the routing is
correct, replace cables on the specified port
until the POST message is eliminated.
1778
Slot x Drive Array resuming Automatic Data
Recovery process.
No action required. This message appears
when a controller resets or power cycle occurs
while Automatic Data Recovery is in progress.
1779
Slot x Drive Array - Replacement drive(s)
detected OR previously failed drive(s)
now
appear to be operational:
Port (y): SCSI ID (
x
): Restore data from
backup if replacement drive
x
has been
installed.
If this message appears and drive
x
(identified
by its SCSI ID)
has not been replaced, this
indicates an intermittent drive failure. This
message also appears once immediately
following drive replacement before data is
restored from backup.
1783
Slot x Drive Array Controller Failure.
If this message appears immediately following
a ROM installation, the ROM is defective or not
installed properly. Check that the controller is
firmly inserted in its slot. Try upgrading the
System ROMs. Otherwise, replace the SMART-
2DH Controller.
1784
Slot x Drive Array Drive Failure. The
following SCSI drive(s) should be replaced:
SCSI Port (y) SCSI ID (
x
)
Check for loose cables. Replace defective drive
x
and/or cable(s).