Craftsman 28813 Operation Manual - Page 27

and install

Page 27 highlights

Weak or Dead Battery Fully Charged Battery REPLACING BATTERY WARNING" Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. 1. Lift seat pan to raised position. 2. Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor. 3. Install new battery with terminals in same position as old battery. 4. First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal 5. Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely. _. (_ Negative (Black) Cable TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Remove bulb holder from the hole in the backside of the grill. 3. Replace bulb in holder and install bulb holder securely back into the hole in the backside of the grill. 4. Close hood. INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Repair Parts section. TO REPLACE FUSE Replace with 30 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. TO REMOVE HOOD AND GRILL ASSEMBLY 1. Raise hood. 2. Unsnap headlight wire connector. 3. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. 4. When replacing hood, be sure to reconnect the headlight wire connector. Headlight Wire Connector Positive (Red) Cable 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68

Weak
or Dead
Fully Charged
Battery
Battery
REPLACING
BATTERY
WARNING"
Do
not short
battery
terminals
by allowing
a wrench
or any
other
object
to contact
both terminals
at
the
same
time.
Before
connecting
battery,
remove
metal
bracelets,
wristwatch
bands,
rings,
etc.
Positive
terminal
must
be connected
first
to prevent
sparking
from
accidental
grounding.
1.
Lift
seat
pan
to
raised
position.
2.
Disconnect
BLACK
battery
cable
first
then
RED
battery
cable
and
carefully
remove
battery
from
tractor.
3.
Install
new
battery
with
terminals
in
same
position
as old
battery.
4.
First
connect
RED
battery
cable
to
positive
(+) terminal
with
hex
bolt
and
keps
nut as
shown.
Tighten
securely.
Slide
terminal
cover
over
terminal
5.
Connect
BLACK
grounding
cable
to
negative
(-) terminal
with
remaining
hex
bolt and
keps
nut. Tighten
securely.
_. (_
Negative
(Black)
Cable
TO
1.
2.
REPLACE
HEADLIGHT
BULB
Raise
hood.
Remove
bulb holder from the hole in
the backside
of the grill.
3.
Replace
bulb in holder
and install
bulb
holder securely
back into the hole in
the backside
of the grill.
4.
Close
hood.
INTERLOCKS
AND
RELAYS
Loose
or damaged
wiring
may
cause
your
tractor
to
run
poorly,
stop
running,
or
prevent
it from
starting.
Check
wiring.
See
electrical
wiring
diagram
in the
Repair
Parts
section.
TO
REPLACE
FUSE
Replace
with
30 amp
automotive-type
plug-in
fuse.
The
fuse
holder
is located
behind
the
dash.
TO
REMOVE
HOOD
AND
GRILL
AS-
SEMBLY
1.
Raise
hood.
2.
Unsnap
headlight
wire
connector.
3.
Stand
in front
of tractor.
Grasp
hood
at
sides,
tilt toward
engine
and
lift off of
tractor.
4.
When
replacing
hood,
be sure
to
re-
connect
the
headlight
wire
connector.
Headlight
Wire
Connector
Positive
(Red)
Cable
27