Craftsman 28813 Operation Manual - Page 9

TO ROLL, TRACTOR, OFF SKID, Operation, function

Get Craftsman 28813 - 46 in. Lawn Tractor PDF manuals and user guides
UPC - 071288130000
View all Craftsman 28813 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

. Connect switch to seat. 3. Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan. Slot ! Tape ADJUST SEAT 1. Sit in seat. 2. Lift up adjustment lever (A) and slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. 3. Release lever to lock seat in position. Flat washer pan Bolt Tab Adjustment handle 4. Push down on seat to engage pads in slots and pull seat towards rear of tractor. 5. Raise seat and tighten bolt securely. 6. Remove tape and discard. 7. Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat. To adjust seat: Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle. CHECK BATTERY 1. Lift seat pan to raised position. NOTE:If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. NOTE: You may now roll your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid. _L, WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects. TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls) 1. Raise attachment lift lever to its highest position. 2. Release parking brake by depressing clutch/brake pedal. 3. Place gearshift lever in neutral (N) position. 4. Roll tractor forward off skid. 5. Remove banding holding the deflector shield up against tractor. CHECK TiRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSi shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly leveled. See "TO LEVEL MOWER" in the Service and Adjustments section of this manual. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
.
3.
Connect
switch
to seat.
Place seat on seat pan so all three
(3)
bottom
pads are positioned
over large
slotted
holes in pan.
Slot
!
Tape
Flat
washer
pan
Adjustment
Bolt
Tab
handle
4.
Push
down
on
seat
to
engage
pads
in
slots
and
pull
seat
towards
rear
of trac-
tor.
5.
Raise
seat
and
tighten
bolt securely.
6.
Remove
tape
and
discard.
7.
Lower
seat
into
operating
position
and
sit on seat.
Press
clutch/brake
pedal
all
the
way
down.
If operating
position
is
not comfortable,
adjust
seat.
To adjust
seat:
Grasp
adjustment
handle
and
pull
up, slide
seat
to
desired
position
and
release
adjustment
handle.
CHECK
BATTERY
1.
Lift seat
pan
to raised
position.
NOTE:If
this
battery
is put
into service
after
month
and
year
indicated
on label
(label
located
between
terminals)
charge
battery
for
minimum
of one
hour
at 6-10
amps.
ADJUST
SEAT
1.
Sit
in seat.
2.
Lift
up adjustment
lever
(A) and
slide
seat
until
a comfortable
position
is
reached
which
allows
you
to
press
clutch/brake
pedal
all the way
down.
3.
Release
lever
to lock
seat
in position.
NOTE:
You may now roll your tractor
off
the skid.
Follow the appropriate
instruction
below to remove
the tractor
from the skid.
_L, WARNING:
Before
starting,
read, un-
derstand
and follow
all instructions
in the
Operation
section
of this manual.
Be sure
tractor
is in a well-ventilated
area. Be sure
the area in
front of tractor
is clear of other
people
and objects.
TO ROLL
TRACTOR
OFF SKID
(See
Operation
section
for
location
and
function
of
controls)
1.
Raise
attachment
lift lever
to
its high-
est
position.
2.
Release
parking
brake
by
depressing
clutch/brake
pedal.
3.
Place
gearshift
lever
in neutral
(N)
position.
4.
Roll
tractor
forward
off skid.
5.
Remove
banding
holding
the
deflector
shield
up against
tractor.
CHECK
TiRE
PRESSURE
The tires on your tractor
were overinflated
at the factory
for shipping
purposes.
Cor-
rect tire pressure
is important
for best
cutting
performance.
•
Reduce
tire pressure
to PSi shown
on
tires.
9
CHECK
DECK
LEVELNESS
For best cutting
results,
mower
hous-
ing should
be properly
leveled.
See "TO
LEVEL
MOWER"
in the Service
and
Adjustments
section
of this manual.