Cub Cadet CC 30 H Operation Manual - Page 11
Controls & Operation - hydro drive
View all Cub Cadet CC 30 H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
Controls & Operation Hydro Transmission (E) (L) (A) (B) (P) (N*) (O) (C) (G) (D) (M) (N*) (K) (J) 30" 6-Speed Transmission (F) (L) (A) (B) (P) (N*) (H) (I) (M) (N*) (K) (J) 3 24" 6-Speed Transmission (F) (B) (P) (H) (I) (J) (K) (N*) (M) Note: This Operator's Manual covers several models. Riding mower features may vary by model. Not all features in this manual are applicable to all riding mower models and the riding mower depicted may differ from yours. Note: References to LEFT, RIGHT, FRONT, and REAR indicate that position on the riding mower when facing forward while seated in the operator's seat. Throttle/Choke Control or Throttle Control Lever (If equipped) (A) Throttle/Choke Control Lever (If equipped) The throttle/choke control lever is located on the left side of the riding mower's dash panel. This lever controls the speed of the engine and, when pushed all the way forward, past the FAST detent position closes the choke for cold starting. When set in a given position, the throttle will maintain a uniform engine speed. Note: When operating the riding mower with the cutting deck engaged, be certain that the throttle/choke SL OW control is always in the FAST position. Throttle Control (If equipped) The throttle control is located on the FAST left side of the riding mower's dash panel. When set in a given position, a uniform engine speed will be maintained. Push the throttle control handle forward to increase the engine speed. The riding mower is designed to operate with the throttle control in the FAST position (full throttle) when the mower deck is engaged. Pull the throttle control handle rearward to decrease the engine speed. SLOW Figure 3-1 Ignition Module (B) WARNING Never leave a running machine unattended. Always disengage PTO, set parking brake, stop engine and remove key to prevent unintended starting. The ignition module is located on the left fender of the riding mower seated in the operator's position, adjacent to the throttle/choke control or throttle control. Ignition Module w/ Reverse Caution Mode (If equipped) To start the engine, insert the key into the ignition switch and turn clockwise to the START position. Release the key into the NORMAL MOWING MODE position once the engine has fired. To stop the engine, turn the ignition key counterclockwise to the STOP position. CAUTION Prior to operating the riding mower, refer to both Safety Interlock Switches and Starting The Engine in the Operation section of this manual for detailed instructions regarding the Ignition Switch Module and operating the riding mower in REVERSE CAUTION MODE . * -- Refer to Oil Fill Cap for location of your oil fill cap. Ignition Module (If equipped) The ignition switch has three positions: STOP - The engine and electrical system is turned off. RUN - The riding mower electrical system is energized. START - The starter motor will turn over the engine. Release the key immediately when the engine starts Note: To prevent accidental starting and/or battery discharge, remove the key from the ignition switch when the riding mower is not in use. Forward Drive Pedal (Hydro riding mowers) (C) The forward drive pedal is located on the right side of the machine, along the running board. Press the forward drive pedal forward to cause the riding mower to travel forward. Ground speed is also controlled with the forward drive pedal. The further forward the pedal is pivoted, the faster the riding mower will travel. The pedal will return to its original/neutral position when it's not pressed. Reverse Drive Pedal (Hydro riding mowers) (D) The reverse drive pedal is located on the right side of the riding mower along the running board. Ground speed is also controlled with the reverse drive pedal. The further downward the pedal is pivoted, the faster the riding mower will travel. The pedal will return to its original/neutral position when it's not pressed. 11