Cub Cadet Challenger 400LX Operation Manual - Page 9

V Power Outlet, Auxiliary Switch Panel, Occupant Protective Structure OPS, Cup Holders, Cargo Bed

Get Cub Cadet Challenger 400LX PDF manuals and user guides View all Cub Cadet Challenger 400LX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

12V Power Outlet The 12V power outlet is located on the right side of the dash panel. It is used for the convenience of plugging in accessories that require a power source with a maximum load of 5A at 12V. Auxiliary Switch Panel The auxiliary switch panel is located on the right hand side of the dash panel above the handhold. When adding accessories requiring switches, use this area of the dash panel to install the desired switches. Occupant Protective Structure (OPS) This utility vehicle is equipped with an Occupant Protection Structure (OPS) and seat belts. When used together they are effective in reducing crushing injuries to the operator and passenger in the event of an accidental rollover or tip-over. The safety provided by the OPS is minimized if the seat belt is not properly adjusted AND buckled. WARNING: Always wear the seat belt when operating the utility vehicle. Cargo Bed The cargo bed maximum capacity is 350lbs. The cargo bed may be tilted for dumping loads. Push forward on the cargo bed latch lever to unlock the bed and manually lift the cargo bed. See Figure 3-1. NOTE: Access to the engine is achieved by raising the cargo bed. IMPORTANT: Do not exceed the vehicle's Total PayLoad Capacity of 850 lb (385 kg), which includes driver, passenger, accessories, tongue load and cargo. Do not exceed 350 lb (158 kg) in the cargo bed. Use the following guidelines when using a utility vehicle equipped with OPS: 1. Be aware of overhead clearances in the area of operation. Check for clearance of door (or gate) openings and other overhead objects such as utility lines and tree branches. Overhead objects could catch the OPS and upset the utility vehicle. 2. Do not modify the OPS by drilling holes for, or welding accessories to the structure. 3. Do not use the OPS to pull objects with the utility vehicle. Use ONLY the utility vehicle hitch for pulling. 4. Do not operate the utility vehicle without the OPS and do not remove the OPS. 5. In the event of an accident, have the OPS carefully inspected and, if necessary, replaced by your Cub Cadet dealer. Do not attempt to repair the OPS. Cup Holders The cup holders are located on top of the dash panel on both the left and right hand sides. WARNING: Never operate this vehicle while under the influence of alcohol or drugs. Doing so can result in serious personal injury or death. Section 3 - Controls and Features 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
9
S
ECTION
3 — C
ONTROLS
AND
F
EATURES
12V Power Outlet
The 12V power outlet is located on the right side
of the dash panel. It is used for the convenience of
plugging in accessories that require a power source
with a maximum load of 5A at 12V.
Auxiliary Switch Panel
The auxiliary switch panel is located on the right
hand side of the dash panel above the handhold.
When adding accessories requiring switches, use
this area of the dash panel to install the desired
switches.
Occupant Protective Structure (OPS)
This utility vehicle is equipped with an Occupant
Protection Structure (OPS) and seat belts. When
used together they are effective in reducing
crushing injuries to the operator and passenger in
the event of an accidental rollover or tip-over. The
safety provided by the OPS is minimized if the seat
belt is not properly adjusted AND buckled.
WARNING:
Always wear the seat belt
when operating the utility vehicle.
Use the following guidelines when using a utility
vehicle equipped with OPS:
1.
Be aware of overhead clearances in the area
of operation. Check for clearance of door (or
gate) openings and other overhead objects
such as utility lines and tree branches.
Overhead objects could catch the OPS and
upset the utility vehicle.
2.
Do not modify the OPS by drilling holes for, or
welding accessories to the structure.
3.
Do not use the OPS to pull objects with the
utility vehicle. Use ONLY the utility vehicle
hitch for pulling.
4.
Do not operate the utility vehicle without the
OPS and do not remove the OPS.
5.
In the event of an accident, have the OPS
carefully inspected and, if necessary, replaced
by your Cub Cadet dealer. Do not attempt to
repair the OPS.
Cup Holders
The cup holders are located on top of the dash panel
on both the left and right hand sides.
WARNING:
Never operate this vehicle
while under the influence of alcohol or
drugs. Doing so can result in serious
personal injury or death.
Cargo Bed
The cargo bed maximum capacity is 350lbs. The
cargo bed may be tilted for dumping loads. Push
forward on the cargo bed latch lever to unlock the
bed and manually lift the cargo bed. See Figure 3-1.
NOTE:
Access to the engine is achieved by raising
the cargo bed.
IMPORTANT:
Do not exceed the vehicle’s Total
PayLoad Capacity of 850 lb (385 kg), which includes
driver, passenger, accessories, tongue load and
cargo. Do not exceed 350 lb (158 kg) in the cargo
bed.