D-Link DFE-2616IX User Guide - Page 61

SNMP Information

Get D-Link DFE-2616IX - Hub - Stackable PDF manuals and user guides
UPC - 790069213885
View all D-Link DFE-2616IX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

♦ Boot Server IP Address. This variable is the IP address of the TFTP server where the configuration file is located. This entry is used only if the S/W Update Control is enabled and your boot protocol is TFTP only; if you are using BOOTP&TFTP mode, or if Send BOOTP Request on Power Up is enabled, the address will be obtained from the BOOTP server. ♦ Boot File Name. The pathname of the configuration file on your TFTP server. If you are using D-View as your TFTP server, this is the pathname of the .CFG file on your hard disk. This entry is used only if your boot protocol is TFTP ONLY; if you are using BOOTP&TFTP mode, or if Use BOOTP to get IP after start up is enabled, the pathname will be obtained from the BOOTP server. For more information about the DFE-2600 series master hub configuration file, see Appendix C, Boot Configuration File. DFE-2600 Stackable Hub - Software Update Menu Software Update Software Update Mode Boot Protocol Boot Server IP Address [210.68.85.36 ] Boot File Name [c:\dfe2600i.cfg ] Last Boot Server IP Address: 210.68.85.35 HELP SAVE EXIT SNMP Information The System Configuration Menu screen shows a variety of information about your hub, and allows you to set the System Name, System Location, and System Contact. These settings can be retrieved from the hub using SNMP Master Hub Setup and Management 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Master Hub Setup and Management
49
♦
Boot Server IP Address
.
This variable is the IP address of the TFTP
server where the configuration file is located. This entry is used only if
the
S/W Update Control
is enabled and your boot protocol is TFTP
only; if you are using BOOTP&TFTP mode, or if
Send BOOTP Re-
quest on Power Up
is enabled, the address will be obtained from the
BOOTP server.
♦
Boot File Name
.
The pathname of the configuration file on your
TFTP server.
If you are using D-View as your TFTP server, this is
the pathname of the .CFG file on your hard disk.
This entry is used
only if your boot protocol is TFTP ONLY; if you are using
BOOTP&TFTP mode, or if
Use BOOTP to get IP after start up
is en-
abled, the pathname will be obtained from the BOOTP server. For
more information about the DFE-2600 series master hub configuration
file, see
Appendix C,
Boot Configuration File.
DFE-2600 Stackable Hub - Software Update Menu
Software Update
<Disable>
Software Update Mode
<Network
>
Boot Protocol
<TFTP ONLY >
Boot Server IP Address
[210.68.85.36
]
Boot File Name
[c:\dfe2600i.cfg
]
Last Boot Server IP Address:
210.68.85.35
HELP
SAVE
EXIT
SNMP Information
The System Configuration Menu screen shows a variety of information about
your hub, and allows you to set the System Name, System Location, and
System Contact.
These settings can be retrieved from the hub using SNMP