D-Link DPG-1200 User Manual - Page 42

The recommended player is installed, but it still doesn't work?

Get D-Link DPG-1200 - PC-on-TV Media Player PDF manuals and user guides
UPC - 790069308772
View all D-Link DPG-1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Section 7 - Frequently Asked Questions The recommended player is installed, but it still doesn't work? Check to see if DirectDraw is enabled. 1. Open Windows® Start, Run, and type: dxdiag 2. Wait for the diagnostic to run. 3. Click on the Video 2 tab, which should correspond to the PC-on-TV device. If DirectDraw is disabled, click on the Enable button. The DirectDraw players such as PowerDVD should now work. Can the Internet be accessed while projecting through the PC-on-TV device? The Internet can be accessed either through the computer, the PC-on-TV device, or a wireless access point (if one already exists while being projected onto the display). If the Internet is accessed via the PC-on-TV device, it is advised that the Ethernet cable be connected to the PC-on-TV device before it is powered up. Note the following special cases: • The Ethernet port on the board can have DHCP enabled or STATIC addresses. This can be accomplished from within the PC-on-TV device application. • Port 80 should be open on the LAN to allow access to the Internet. • Port 21 should be open on the LAN to allow PC-on-TV device firmware updates. • The DHCP allocation range is 10.0.0.2 through 10.0.0.254 (IP/subnet of PC-on-TV device Ethernet port should be different than 10.0.0.x). • The PC-on-TV device Ethernet port has a 'dummy' MAC address by default. During the manufacturing process, each device is programmed with a unique MAC address. This is necessary to avoid MAC address conflict and improper operation of the device. Note that with a dummy MAC address, there may be some computers which may not be able to connect to the device. D-Link DPG-1200 User Manual 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
³±
D-Link DPG-1±00 User Manual
Section ¸ - Frequently Asked Questions
The recommended player is installed, but it still doesn’t work?
Check to see if DirectDraw is enabled.
1. Open Windows
®
Start, Run, and type: dxdiag
2. Wait for the diagnostic to run.
3. Click on the Video 2 tab, which should correspond to the PC-on-TV device.
If DirectDraw is disabled, click on the Enable button. The DirectDraw players such as PowerDVD should now work.
Can the Internet be accessed while projecting through the PC-on-TV device?
The Internet can be accessed either through the computer, the PC-on-TV device, or a wireless access point (if one
already exists while being projected onto the display).
If the Internet is accessed via the PC-on-TV device, it is advised that the Ethernet cable be connected to the PC-on-TV
device before it is powered up.
Note the following special cases:
• The Ethernet port on the board can have DHCP enabled or STATIC addresses. This can be accomplished from
within the PC-on-TV device application.
• Port 80 should be open on the LAN to allow access to the Internet.
• Port 21 should be open on the LAN to allow PC-on-TV device firmware updates.
• The DHCP allocation range is 10.0.0.2 through 10.0.0.254 (IP/subnet of PC-on-TV device Ethernet port should
be different than 10.0.0.x).
• The PC-on-TV device Ethernet port has a ‘dummy’ MAC address by default. During the manufacturing
process,
each device is programmed with a unique MAC address. This is necessary to avoid MAC address conflict and
improper operation of the device. Note that with a dummy MAC address, there may be some computers which
may not be able to connect to the device.