Dell Alienware Area-51 Threadripper Edition R3 Alienware Area-51 Threadripper - Page 62

Replacing the drive-bay heat sensor cable, Procedure, Post-requisites

Get Dell Alienware Area-51 Threadripper Edition R3 PDF manuals and user guides View all Dell Alienware Area-51 Threadripper Edition R3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Replacing the drive-bay heat sensor cable WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure 1 Route the drive-bay heat-sensor cable through the slot on the chassis. 2 Align the tab on the drive-bay heat-sensor cable on the chassis. 3 Push the release tab on the drive-bay heat-sensor cable and press it into place. 4 Lay the chassis on the left side. 5 Connect the drive-bay heat-sensor cable to the system board. See "system- board components".. Post-requisites 1 Replace the left and right side-panels. See "Replacing the side panels". 2 Replace the stability foot. 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
Replacing the drive-bay heat
sensor cable
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in
Before working inside your computer
. After working inside your
computer, follow the instructions in
After working inside your computer
.
For more safety best practices, see the Regulatory Compliance home
page at
www.dell.com/regulatory_compliance
.
Procedure
1
Route the drive-bay heat-sensor cable through the slot on the chassis.
2
Align the tab on the drive-bay heat-sensor cable on the chassis.
3
Push the release tab on the drive-bay heat-sensor cable and press it into
place.
4
Lay the chassis on the left side.
5
Connect the drive-bay heat-sensor cable to the system board. See “
system-
board components
”..
Post-requisites
1
Replace the left and right side-panels. See “
Replacing the side panels
”.
2
Replace the
stability foot
.
62