Dell Force10 E600i E600 TeraScale Installation Guide - Page 31

To install line cards and RPMs, Installing RPM into the E600i

Get Dell Force10 E600i PDF manuals and user guides View all Dell Force10 E600i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Step Task 5 Follow the same installation procedure for the remaining cards and slots, in the appropriate order. NOTE: The blank panels do not have circuit boards or levers. Align the blank with the guides and gently slide toward the backplane. Figure 7-1. Installing RPM into the E600i FN00079A To install line cards and RPMs: Step 1 2 3 4 5 Task Remove the line card from its box and carefully remove the line card from the anti-static packaging. Align the RPM with the guide and gently slide it into the slot until you feel the connectors engage with the chassis backplane. NOTE: Hold the card by the edges. Avoid touching the printed circuit board and connector pins. Extend the top and bottom card levers before you insert the card into the slot. Rotate the levers to seat the backplane connectors and line card in place. Secure card and blanks in place by tightening the top and captive screws on each card. Follow the same installation procedure for the remaining cards and slots, in the appropriate order. NOTE: The blank panels do not have circuit boards or levers. Align the blank with the guides and gently slide toward the backplane. Installing RPMs, Line Cards, and SFMs | 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Installing RPMs, Line Cards, and SFMs
|
31
NOTE:
The blank panels do not have circuit boards or levers. Align the blank with the guides and gently slide
toward the backplane.
Figure 7-1.
Installing RPM into the E600i
To install line cards and RPMs:
NOTE:
The blank panels do not have circuit boards or levers. Align the blank with the guides and gently slide
toward the backplane.
5
Follow the same installation procedure for the remaining cards and slots, in the appropriate order.
Step
Task
1
Remove the line card from its box and carefully remove the line card from the anti-static packaging.
2
Align the RPM with the guide and gently slide it into the slot until you feel the connectors engage with the chassis
backplane.
NOTE:
Hold the card by the edges. Avoid touching the printed circuit board and connector pins. Extend the
top and bottom card levers before you insert the card into the slot.
3
Rotate the levers to seat the backplane connectors and line card in place.
4
Secure card and blanks in place by tightening the top and captive screws on each card.
5
Follow the same installation procedure for the remaining cards and slots, in the appropriate order.
Step
Task
FN
0007
9
A