Dell Force10 S60-44T Installing the S60 System - Page 45

SD Card Removal, For more information, contact the Dell Force10 Technical Assistance Center TAC see

Get Dell Force10 S60-44T PDF manuals and user guides View all Dell Force10 S60-44T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Dell Force10 products, which fall within the scope of the WEEE, are labeled with the crossed-out wheelie-bin symbol, as shown above, as required by WEEE. For information on Dell Force10 product recycling offerings, see the WEEE Recycling instructions on iSupport at: https://www.force10networks.com/CSPortal20/Support/WEEEandRecycling.pdf. For more information, contact the Dell Force10 Technical Assistance Center (TAC) (see Contacting the Technical Assistance Center). SD Card Removal To support high-security environments, you can remove and re-install the SD card. Dell Force10 recommends only removing the card when necessary. Only authorized personnel should remove and replace the card. CAUTION: Only remove the SD card to support high-security operations and after discussions with Dell Force10 Technical Support or your Dell Force10 representative. To remove the SD card, follow these steps: Step Task 1 Remove the small Phillips screws that connect the top to the body. There are three screws evenly spaced across the rear and three screws evenly spaced along each side of the case. 2 Slide the top backwards until its front flange slides free of the faceplate. Lift it off. 3 Gently push the SD card to release it from the slot. 4 Remove the card. S60 Specifications | 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
S60 Specifications
|
45
Dell Force10 products, which fall within the scope of the WEEE, are labeled with the crossed-out
wheelie-bin symbol, as shown above, as required by WEEE.
For information on Dell Force10 product recycling offerings, see the WEEE Recycling instructions on
iSupport at:
https://www
.force10networks.com/CSPortal20/Support/WEEEandRecycling.pdf
.
For more information, contact the Dell Force10 Technical Assistance Center (TAC) (see
Contacting the
T
echnical
Assistance Center
).
SD Card Removal
To support high-security environments, you can remove and re-install the SD card. Dell Force10
recommends only removing the card when necessary. Only authorized personnel should remove and
replace the card.
CAUTION:
Only remove the SD card to support high-security operations and after discussions with Dell
Force10 Technical Support or your Dell Force10 representative.
To remove the SD card, follow these steps:
Step
Task
1
Remove the small Phillips screws that connect the top to the body. There are three screws evenly spaced across
the rear and three screws evenly spaced along each side of the case.
2
Slide the top backwards until its front flange slides free of the faceplate. Lift it off.
3
Gently push the SD card to release it from the slot.
4
Remove the card.