Denon AVR2307CI Owners Manual - English - Page 76

ENGLISH Troubleshooting Symptom No sound is produced from subwoofer. Cause Measures • Subwoofer's power is not on. • Turn on the power. • Subwoofer's initial setting is set to • Set the setting to "YES". "NO". • Subwoofer's output is not connected. • Connect properly. • The subwoofer's channel volume • Turn the subwoofer's channel volume level is set to "OFF". level up. Page - 60 8, 23 36 No test tones are produced. • Surround mode is set to a mode • Set to STANDARD (Dolby/DTS - other than STANDARD (Dolby/DTS Surround). Surround). No sound is produced • Surround mode is set to "STEREO". • Set to a mode other than "STEREO". - from surround speakers. This unit does not • Batteries dead. • Replace with new batteries. 3 operate properly when • Remote control unit too far from this • Move closer. 3 remote control unit is unit. used. • Obstacle between this unit and • Remove obstacle. 3 remote control unit. • Different button is being pressed. • Press the proper button. - • < and > ends of batteries inserted • Insert batteries properly. 3 in reverse. An image is not • AVR-2307CI's HDMI output terminals • Check the HDMI connection. 19 projected with an HDMI and monitor's input terminals are not connection. properly connected. • No HDMI signal is being input. • Properly select HDMI signal input 53 source. • The connected monitor equipment or • The AVR-2307CI will not output video 19 other equipments do not support signal unless the other equipment HDCP. supports HDCP. • The output format of the connected • Check whether the output format of 19 player (HDMI FORMAT) does not the connected player (HDMI match the supported input format of FORMAT) matches the supported connected monitor equipments. input format of connected monitor equipments. The HDMI audio is not • The AVR-2307CI does not play HDMI • Set the HDMI audio playback setting 53 output. audio signals. at the "HDMI In Assignment" settings to "AMP". • The HDMI audio signals are not • Set the HDMI audio playback setting 53 output from the connected monitor at the "HDMI In Assignment" device. settings to "TV". Troubleshooting Symptom Cause Measures Page Power has turned off • The set's internal temperature has • Put the AVR-2307CI in a well- 8 and the power indicator risen and the protection circuit has ventilated place. is blinking red. been activated. • Turn off the power, then wait for the 8 set to fully cool off before turning the power back on. • The core wires of the speaker cables • Check the connections of all the 8 are touching each other or the AVR- speaker cables. 2307CI's rear panel, activating the protection circuit. • AVR-2307CI is malfunctioning. • Turn off the power and contact a 8 DENON customer service center. Sound is only produced • You are playing a monaural source • When playing monaural sources, 35 from the center speaker. (TV, AM radio broadcast, etc.) in the select a surround mode other than STANDARD (Dolby/DTS Surround) STANDARD (Dolby/DTS Surround) mode. mode. "DOLBY DIGITAL" is not • DVD player's digital audio output • Check the DVD player's audio output - displayed. setting is not proper. setting. For details, see the DVD player's operating instructions. "CHECK ANTENNA" is • AVR-2307CI's XM connectors and the • Check that the connection are 22 displayed in the XM XM Passport System is not properly correct. mode. connected. "NO SIGNAL" is displayed in the XM mode. • The signal cannot be received. • Reposition your XM Passport System. 39 "OFF AIR" is displayed • The selected channel is not currently • Select the another channel. 39 in the XM mode. broadcasting. Receiving only XM • The XM Tuner is not activated. • Contact XM Radio. 38 channels 0 and 1. 73 ENGLISH