Dewalt DW723 Instruction Manual - Page 7

Locking Locator Clip, Removing the Saw, Carry Handle, Accessories, Repairs, Three Year Limited - parts

Page 7 highlights

English Locking Locator Clip The locking locator clip (G) keeps the saw from sliding left or right during cutting operations. To move the clip, remove saw/bracket assembly, loosen the screw in the center of the clip, slide it to the desired position and tighten the screw. You can then remount the saw/bracket in the new location. Removing the Saw Once the miter saw is fastened to the brackets, it can be removed by grasping the release levers, pulling up slightly to clear the beam and can be set down on the rubber feet for transportation or cleaning. Carry Handle A handle has been supplied to safely transport the Miter Saw Stand to and from the work site. WARNING: To reduce the risk of personal injury, DO NOT attempt to store the stand - with or without the saw attached - in a vertical position. Loss of control may result. Accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, do not create unstable conditions and use only with DEWALT miter saws. Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website www. dewalt.com. Repairs To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should be performed by a DEWALT factory service center, a DEWALT authorized service center or other qualified service personnel. Always use identical replacement parts. Three Year Limited Warranty DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces. In addition to the warranty, DEWALT tools are covered by our: 1 YEAR FREE SERVICE DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

5
English
Locking Locator Clip
The locking locator clip (G) keeps the saw from sliding left or right
during cutting operations. To move the clip, remove saw/bracket
assembly, loosen the screw in the center of the clip, slide it to the
desired position and tighten the screw. You can then remount the
saw/bracket in the new location.
Removing the Saw
Once the miter saw is fastened to the brackets, it can be removed by
grasping the
release levers, pulling up slightly to clear the beam and
can be set down on the rubber feet for transportation or cleaning.
Carry Handle
A handle has been supplied to safely transport
the Miter Saw Stand to and from the work site.
WARNING:
To reduce the risk of personal
injury,
DO NOT
attempt to store the stand –
with or without the saw attached – in a vertical
position. Loss of control may result.
Accessories
WARNING:
Since accessories, other than those offered by
D
E
WALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the risk of
injury, do not create unstable conditions and use only with D
E
WALT
miter saws.
Recommended accessories for use with your tool are available at
extra cost from your local dealer or authorized service center. If you
need assistance in locating any accessory, please contact D
E
WALT
Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286,
call 1-800-4-D
E
WALT (1-800-433-9258) or visit our website www.
dewalt.com.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustments should be performed by a D
E
WALT factory service
center, a D
E
WALT authorized service center or other qualified
service personnel. Always use identical replacement parts.
Three Year Limited Warranty
D
E
WALT will repair, without charge, any defects due to faulty
materials or workmanship for three years from the date of purchase.
This warranty does not cover part failure due to normal wear or
tool abuse. For further detail of warranty coverage and warranty
repair information, visit www.dewalt.com or call 1-800-4-D
E
WALT
(1-800-433-9258). This warranty does not apply to accessories or
damage caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and you may
have other rights which vary in certain states or provinces.
In addition to the warranty, D
E
WALT tools are covered by our:
1 YEAR FREE SERVICE
D
E
WALT will maintain the tool and replace worn parts caused by
normal use, for free, any time during the first year after purchase.