Dewalt DWE4517 Instruction Manual - Page 13

Mounting and Removing Hubbed Wheels, Sanding Flap Discs - nut

Get Dewalt DWE4517 PDF manuals and user guides View all Dewalt DWE4517 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

English 3. With the guard latch open, rotate the FIG. 7 guard into the desired working position that provides maximum I protection to the user as shown. 4. Close the guard latch to secure the guard on the gear case. You should be unable to rotate the guard by hand when the latch is closed. Do not operate the grinder with a loose guard or the guard latch in open position. 5. To remove the guard, follow the procedure above in reverse order. NOTE: The guard is pre-adjusted to the diameter of the gear case hub at the factory. If, after a period of time, the guard becomes loose, tighten the adjusting screw (J) with clamp in the closed position. NOTICE: Do not tighten the adjusting screw with the guard latch in open position. Undetectable damage to the guard or the mounting hub may result. J Mounting and Removing Hubbed Wheels Hubbed wheels install directly on the 5/8"-11 threaded spindle. 1. Thread the wheel on the spindle by hand, seating the wheel against the soft mount. 2. Depress the spindle lock button and use a wrench to tighten the hub of the wheel. 3. Reverse the above procedure to remove the wheel. Sanding Flap Discs soft mount 445928-01 soft mount 445928-01 Type 27 guard D284937 7" D284939 9" hubbed sanding flap disc Type 27 guard D284937 7" D284939 9" backing flange 54339-00 non-hubbed sanding flap disc clamp nut 22191-00 NOTE: Wheel size must match guard size; i.e., a new 7" wheel may not be used with a 9" guard. The bottom surface of wheel must be inside the bend of the guard lip. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
3. With the guard latch open, rotate the
I
J
FIG. 7
guard into the desired working
position that provides maximum
protection to the user as shown.
4. Close the guard latch to secure the
guard on the gear case. You should
be unable to rotate the guard by
hand when the latch is closed. Do
not operate the grinder with a loose
guard or the guard latch in open
position.
5. To remove the guard, follow the
procedure above in reverse order.
NOTE:
The guard is pre-adjusted to
the diameter of the gear case hub at
the factory. If, after a period of time,
the guard becomes loose, tighten the
adjusting screw (J) with clamp in the
closed position.
NOTICE:
Do not tighten the adjusting
screw with the guard latch in open
position. Undetectable damage to the
guard or the mounting hub may result.
Mounting and Removing Hubbed Wheels
Hubbed wheels install directly on the 5/8"–11 threaded spindle.
1. Thread the wheel on the spindle by hand, seating the wheel
against the soft mount.
2. Depress the spindle lock button and use a wrench to tighten the
hub of the wheel.
3. Reverse the above procedure to remove the wheel.
soft mount
445928-01
Type 27 guard
D284937 7"
D284939 9"
backing flange
54339-00
non-hubbed sanding
flap disc
clamp nut
22191-00
Sanding Flap Discs
soft mount
445928-01
Type 27 guard
D284937 7"
D284939 9"
hubbed sanding
flap disc
NOTE:
Wheel size must match guard size; i.e., a new 7" wheel may
not be used with a 9" guard. The bottom surface of wheel must be
inside the bend of the guard lip.
English
11