Epson AcuLaser CX11NF Start Here Card - Page 3

Install Photoconductor, Set Fax/Printer Information, CX11NF, CX11N - photoconductor reset

Get Epson AcuLaser CX11NF PDF manuals and user guides View all Epson AcuLaser CX11NF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

3 Install Photoconductor Caution: Make sure the CX11N is turned on and you have installed all the toner cartridges, as described in the previous section. 1 Install Photoconductor appears in the LCD screen. Lift up the scanner. 2 Lift up cover B and raise the orange lever inside, on the right. 3 Remove the photoconductor from its package and pull off the protective sheet. Caution: Do not touch the belt on the top of the photoconductor or the blue roller beneath it; otherwise, print quality may decrease. Avoid exposing the photoconductor to light any longer than necessary. Do not touch any other components inside the CX11N. 4 Hold the photoconductor by its handle and insert it into the slots marked with blue arrows inside the CX11N. Push it in until it clicks into place. 5 Flip down the orange lever, then close cover B. 6 Pull out the extension tray if necessary. Lower the scanner unit to its original position. 4 Set Fax/Printer Information CX11NF 1 Select the Country: Press the or button to select the country, then press the button. 2 Select the Language: Press the or button to select the language, then press the button. 3 Set the Date and Time: Press the or button to select the year, month, day, hour, and minute. Press the button after selecting each item. The CX11NF then resets itself and reboots. 4 Turn off the CX11NF. 5 Connect an RJ-11 cord to the telephone line interface on the CX11NF and to the RJ-11 jack on the wall. Note: An RJ-11 cord is not included with the CX11NF. 6 Turn on the CX11NF. CX11N 1 Press the Setup button. The Setup light turns on and the LCD screen shows Setup Mode for a few seconds, then changes to the Setup menu screen. 2 Press the ▼ button until Printer Settings is selected, then press the button. 3 Press the ▼ button until Setup Menu is selected, then press the button. ▲ ▲

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Install Photoconductor
Caution:
Make sure the CX11N is turned on and you have installed all the toner
cartridges, as described in the previous section.
1
Install Photoconductor
appears in the LCD screen. Lift up the scanner.
2
Lift up cover B and raise the orange lever
inside, on the right.
3
Remove the photoconductor from its package
and pull off the protective sheet.
Caution:
Do not touch the belt on the top
of the photoconductor or the blue roller beneath
it; otherwise, print quality may decrease.
Avoid exposing the photoconductor to light any longer than necessary.
Do not touch any other components inside the CX11N.
4
Hold the photoconductor by
its handle and insert it into the
slots marked with blue arrows
inside the CX11N. Push it in
until it clicks into place.
5
Flip down the orange lever,
then close cover B.
6
Pull out the extension tray if necessary. Lower the scanner unit to its
original position.
Set Fax/Printer Information
CX11NF
1
Select the Country: Press the
or
button to select the country,
then press the
button.
2
Select the Language: Press the
or
button to select the language,
then press the
button.
3
Set the Date and Time: Press the
or
button to select the year,
month, day, hour, and minute. Press the
button after selecting each
item. The CX11NF then resets itself and reboots.
4
Turn off the CX11NF.
5
Connect an RJ-11 cord to
the telephone line interface
on the CX11NF and to the
RJ-11 jack on the wall.
Note:
An RJ-11 cord is not
included with the CX11NF.
6
Turn on the CX11NF.
CX11N
1
Press the
Setup
button.
The Setup light turns on and the LCD screen shows
Setup Mode
for a
few seconds, then changes to the Setup menu screen.
2
Press the
▼
button until
Printer Settings
is selected, then press the
▲
button.
3
Press the
▼
button until
Setup Menu
is selected, then press the
▲
button.
4
3