Fisher and Paykel E522BRWFD5 User Guide - Page 16

Installation instructions

Get Fisher and Paykel E522BRWFD5 PDF manuals and user guides View all Fisher and Paykel E522BRWFD5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

INSTALLATION INSTRUCTIONS Installation instructions: 1 Ensure the refrigerator is NOT plugged into a power supply. 2 Locate a cold water supply/feed only suitable for a water connection. Tee and tap fitting is not supplied. 3 Connect the 8" (200 mm) blue tubing to the outlet of the PRV (blue collet) and the inlet connection of the water filter cartridge as shown in Diagram 1. Gently pull on both ends to ensure it is locked. 4 Connect the white ¼" (6 mm) tubing to the outlet of the water filter cartridge as shown in Diagram 2. Gently pull to ensure it is locked. 5 Measure the required length of tubing to run from the PRV to the water connection point (no less than 10" (250 mm)). 6 Cut the tubing making sure the ends are square and clean. 7 Connect the tubing to the faucet connection and the base of the PRV (white collet) and then to the faucet as shown in Diagram 3. Please note that the faucet connection supplied should fit most installation situations. 8 Connect one locking key to each side of the water filter cartridge in between the cartridge and the locking collet as shown in Diagram 4. 9 To flush the water filter of any trapped air, harmless carbon fines and to also check for leaks, aim the end of the tubing into a bucket, turn isolating faucet on and run at least 10 qt (10 L) of water through. Once complete, turn isolating faucet off. !0 Locate desired position for water filter noting carefully the following points: ●● It is recommended to fit the water filter in a vertical orientation with the water filter head at the top. This will minimize water leakage when replacing cartridge. ●● Ensure the filter is in a convenient location to access every 6 months for replacement. We suggest that this location is beside the water filter supply faucet in a cupboard beside the refrigerator. ●● A minimum clearance of 2 ½" (64 mm) from the bottom of the filter cartridge is required to perform cartridge removal. ●● Do not screw water filter to refrigerator. 14 INLET Diagram 1 PRV connection Diagram 2 Waterline connection to refrigerator Diagram 3 Faucet connection Diagram 4 Locking key

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
14
INSTALLATION INSTRUCTIONS
Installation instructions:
1
Ensure the refrigerator is NOT plugged into a
power supply.
2
Locate a cold water supplyÀfeed only suitable
for a water connection. Tee and tap fitting is
not supplied.
3
Connect the 8” (200 mm) blue tubing to the
outlet of the PRV (blue collet) and the inlet
connection of the water filter cartridge as
shown in Diagram 1. Gently pull on both ends to
ensure it is locked.
4
Connect the white ¿” (6 mm) tubing to the
outlet of the water filter cartridge as shown in
Diagram 2. Gently pull to ensure it is locked.
5
Measure the required length of tubing to run
from the PRV to the water connection point (no
less than 10” (250 mm)).
6
Cut the tubing making sure the ends are square
and clean.
7
Connect the tubing to the faucet connection
and the base of the PRV (white collet) and then
to the faucet as shown in Diagram 3. Please
note that the faucet connection supplied should
fit most installation situations.
8
Connect one locking key to each side of the
water filter cartridge in between the cartridge
and the locking collet as shown in Diagram 4.
9
To flush the water filter of any trapped air,
harmless carbon fines and to also check for
leaks, aim the end of the tubing into a bucket,
turn isolating faucet on and run at least 10 qt
(10 L) of water through. Once complete, turn
isolating faucet off.
!0
Locate desired position for water filter noting
carefully the following points:
●
±
It is recommended to fit the water filter in a
vertical orientation with the water filter head
at the top. This will minimize water leakage
when replacing cartridge.
●
±
Ensure the filter is in a convenient location to
access every 6 months for replacement. We
suggest that this location is beside the water
filter supply faucet in a cupboard beside the
refrigerator.
●
±
A minimum clearance of 2 Á” (64 mm) from
the bottom of the filter cartridge is required
to perform cartridge removal.
●
±
Do not screw water filter to refrigerator.
Diagram 2
Waterline connection to
refrigerator
INLET
Diagram 4
Locking key
PRV connection
Diagram 1
Diagram 3
Faucet connection