Garmin zumo 395LM Owners Manual - Page 22

2 Remove the end piece, the silver tip , and the fuse . Á Â 3 Insert a new fast-blow fuse that has the same current, such as 1 A or 2 A. 4 Place the silver tip in the end piece. 5 Push in the end piece and rotate it clockwise to lock it back into the vehicle power cable . Ã Troubleshooting The suction cup will not stay on my windshield 1 Clean the suction cup and windshield with rubbing alcohol. 2 Dry with a clean, dry cloth. 3 Mount the suction cup (Installation, page 1). My device is not acquiring satellite signals • Verify the GPS simulator is turned off (Navigation Settings, page 16). • Take your device out of parking garages and away from tall buildings and trees. • Remain stationary for several minutes. The device does not charge in my vehicle • Check the fuse in the vehicle power cable (Changing the Fuse in the Vehicle Power Cable, page 17). • Verify the vehicle is turned on and is supplying power to the power outlet. • Verify the interior temperature of the vehicle is within the charging temperature range indicated in the specifications. • Verify the fuse is not broken in the vehicle power outlet. My battery does not stay charged for very long • Decrease the screen brightness (Display Settings, page 16). • Shorten the display timeout (Display Settings, page 16). • Decrease the volume (Adjusting the Volume, page 4). • Disable Bluetooth wireless technology (Disabling Bluetooth, page 16). • Put the device in power saving mode when not in use (Turning the Device On or Off, page 3). • Keep your device away from extreme temperatures. • Do not leave your device in direct sunlight. My device does not appear as a removable drive on my computer On most Windows computers, the device connects using Media Transfer Protocol (MTP). In MTP mode, the device appears as a portable device and not as a removable drive. MTP mode is supported by Windows 7, Windows Vista®, and Windows XP Service Pack 3 with Windows Media Player 10. My device does not appear as a portable device on my computer On Mac computers and some Windows computers, the device connects using USB mass storage mode. In USB mass storage mode, the device appears as a removable drive or volume, and not as a portable device. Windows versions prior to Windows XP Service Pack 3 use USB mass storage mode. My device does not appear as either a portable device or a removable drive or volume on my computer 1 Disconnect the USB cable from your computer. 2 Turn off the device. 3 Connect the USB cable to your device and to a USB port on your computer. TIP: The USB cable must connect to a USB port on your computer, not to a USB hub. The device turns on automatically and goes into MTP mode or USB mass storage mode. A picture of the device connected to a computer appears on the device screen. NOTE: If you have several network drives mapped on your computer, Windows may have trouble assigning drive letters to your Garmin drives. For information about assigning drive letters, see the help file for your operating system. My phone will not connect to the device • Select Settings > Bluetooth. The Bluetooth field must be set to Enabled. • Enable Bluetooth wireless technology on your phone and bring your phone within 33 ft. (10 m) of the device. • Go to www.garmin.com/bluetooth for more help. Appendix Installing a Memory Card for Maps and Data You can install a memory card to increase the storage space for maps and other data on your device. You can purchase memory cards from an electronics supplier, or go to www.garmin.com /maps to purchase a memory card with pre-loaded Garmin mapping software. The device supports microSD and microSDHC memory cards. 1 Locate the memory card slot on your device (Device Overview, page 3). 2 Insert a memory card into the slot. 3 Press it in until it clicks. Data Management You can store files on your device. The device has a memory card slot for additional data storage. NOTE: The device is not compatible with Windows 95, 98, Me, Windows NT®, and Mac OS 10.3 and earlier. About Memory Cards You can purchase memory cards from an electronics supplier, or purchase pre-loaded Garmin mapping software (www.garmin.com). In addition to map and data storage, the memory card can be used to store files such as maps, images, geocaches, routes, waypoints, and custom POIs. Connecting the Device to Your Computer You can connect the device to your computer using a USB cable. 1 Plug the small end of the USB cable into the port on the device. 2 Plug the larger end of the USB cable into a port on your computer. A picture of your device connected to a computer appears on the device screen. Depending on your computer operating system, the device appears as either a portable device, a removable drive, or a removable volume. 18 Troubleshooting