GE DPGT750GCPL Owners Manual - Page 40

Reconnect Washer, Control Board, Attach Washer Control, Board To New Backsplash, Attach Washer

Get GE DPGT750GCPL - Profile Harmony 7.3 cu. Ft. Capacity King-Size Gas Dryer PDF manuals and user guides
UPC - 084691079743
View all GE DPGT750GCPL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Installation Instructions 12 ATTACH WASHER CONTROL BOARD TO NEW BACKSPLASH Replace the four screws removed from the control board earlier. 14 ATTACH WASHER BACKSPLASH Using the two small screws removed earlier, screw the new washer backsplash onto the rear cover. Screws The control board will now be on the opposite side of the washer backsplash. 13 RECONNECT WASHER CONTROL BOARD Connect the washer control board to the new backsplash by sliding the ribbon connector on the new backsplash onto the metal pins on the control board and pushing in. Make sure the ribbon is not twisted before inserting the connector. Place the gray wire from the serial port under the strain relief on the new backsplash. Strain Relief Insert the tabs on the bottom front of the backsplash into the slots on the washer and rotate the backsplash into place. Press the rear of the backsplash down to make sure it fits properly. Secure the new backsplash to the washer using the two long screws removed earlier. 15 RECONNECT POWER SUPPLY TO WASHER AND DRYER • Plug the washer and dryer back in. • Press the POWER buttons on both the washer and dryer to make sure both control boards are properly connected. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
40
Installation Instructions
RECONNECT WASHER
CONTROL BOARD
Connect the washer control board to the
new backsplash by sliding the ribbon
connector on the new backsplash onto the
metal pins on the control board and pushing
in. Make sure the ribbon is not twisted
before inserting the connector.
ATTACH WASHER CONTROL
BOARD TO NEW BACKSPLASH
Replace the four screws removed from the
control board earlier.
The control board will now be on the
opposite side of the washer backsplash.
ATTACH WASHER BACKSPLASH
Insert the tabs on the bottom front of the
backsplash into the slots on the washer and
rotate the backsplash into place. Press the
rear of the backsplash down to make sure it
fits properly.
Secure the new backsplash to the washer
using the two long screws removed earlier.
Using the two small screws removed earlier,
screw the new washer backsplash onto the
rear cover.
RECONNECT POWER SUPPLY
TO WASHER AND DRYER
Screws
12
13
15
14
Strain Relief
Place the gray wire from the serial port under
the strain relief on the new backsplash.
•
Plug the washer and dryer back in.
•
Press the
POWER
buttons on both the
washer and dryer to make sure both
control boards are properly connected.