Haier HL26K1 User Manual - Page 35

ENTER, CH+/CH, Remote

Get Haier HL26K1 - K-Series - 26inch LCD TV PDF manuals and user guides
UPC - 688057324296
View all Haier HL26K1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Remote Control Operation 5. When the device turns ON, press and release ENTER key to program the remote with the new code, saving the code and exit. To exit without programming, press any key other except CH+/CH- and ENTER. LED will be off after manually scan mode is exit. 6. If the device responds, no further programming is required. If the device does not respond, repeat step 1 through 5.And searching will start from current code set. If no key was pressed in 30 seconds, manually scan mode will be automatically exit. 7. After searching the entire data base, this mode will be automatically exited and led will blink for 3 times. Automatic Scan Programming the Remote To automatic scan program the remote: 1. Manually turn OFF the device you wish to power scan. (TV, DVD, VCR, STB, cable box or audio equipment). 2. Press SELECT key to choose the device you wish to program. While Press and holding ENTER key, press SELECT key and device LED will be ON. Keep the status for about 5 seconds, release both keys and then LED will blink twice per second, indicating that the Control is ready for programming. 3. Press and release MUTE key to enter automatic scan mode. And the remote will automatically sending power codes to the device. 4. When the device turns ON, press ENTER key to program the remote with the new code, saving it and exit. To exit without programming, press any key other except ENTER key. 5. If the device responds, no further programming is required. If the device does not respond, repeat steps 1 through 4. And search will start from current code set. 6. After searching the entire data base, this mode will be automatically exited and led will blink for 3 times. Punch-Through Features The remote provides two punch-through features that allow users to control TV volume and DVD or VCR operation while the remote is in another device mode control certain features of another device. Volume Punch-Through: The TV Volume/Mute punch-through feature allows you to control the volume and mute function of your TV while the remote is in another device mode. The feature is applicable for all devices and brands that do not use the volume control buttons for other purposes. Transport Key Punch-Through: The DVD or VCR transport key punch through feature lets you remote the PLAY, STOP, PAUSE, REWIND, FF and RECORD functions of your DVD or VCR while the control operates in other modes. The feature is applicable for all devices and brands that do not use the transport keys for other purposes. Protection mode 1. While press and holding ENTER, press FREEZE key for 5 seconds to enter protection mode. In this mode, all the above programming methods will be invalid. 2.To exit protection: While press and holding ENTER, press FREEZE key. Current device related LED remains ON and then release ENTER and FREEZE. Input three digit password 8 8 8 , LED turns off and protection mode is ended. If error password is input or no password input in 10 seconds, LED blinks three times and then turns off. Protection mode will remain. Display mode 1.To enter display mode, while press and holding ENTER key, press SELECT key and device LED will be ON, keep the status for about 5 seconds. Release both keys and then LED will blink 2 times per second, indicating remote is ready for programming. 2.Sequence press 9, 8, 0 to enter display mode. And LED is off now. 3.Press digit 1 key to get the first digit of current code set. For example, if the first digit of code set is 1, so then led will blink once and remains OFF. Digit 0 in code set will not be displayed. Blink twice per second. 4.Press digit 2 key to get the second digit of current code set. For example, if the second digit of code set is 3, so then led will blink three times and remains OFF. Blink twice per second. 5.Press digit 3 key to get the third digit of current code set. Blink twice per second. 6.Only digit 1, 2, 3 are valid in this mode. And the sequence is not fixed. You can repeat, if you don't remember clearly. 7.Remote will not send out data in this mode if user presses any keys other than digit 1, 2, 3. And this can be regarded as no key pressed. 8.If no key was pressed in 10 seconds or any key other than digit 1, 2, 3 is pressed display mode is ended. Owner s Manual 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Owner s Manual
35
Operation
Remote Control
5. When the device turns ON, press and release
ENTER
key to program the remote with the
new code, saving the code and exit. To exit without programming, press any
key other
except
CH+/CH-
and
ENTER
. LED will be off after manually scan mode is exit.
6. If the device responds, no further programming is required. If the device does not respond,
repeat step 1 through 5.And searching will start from current code set. If no key was
pressed in 30 seconds, manually scan mode will be automatically exit.
7. After searching the entire data base, this mode will be automatically exited and led will
blink for 3 times.
Remote
emote
ENTER
ENTER
emote
ENTER
emote
emote
ENTER
ENTER
ENTER
ENTER
emote
emote
Automatic Scan Programming the
To automatic scan program the r
:
1. Manually turn OFF the device you wish to power scan. (TV, DVD, VCR,
STB, cable box or
audio equipment).
2. Press
SELECT
key to choose the device you wish to program.
While Press and holding
key
,
press
SELECT
key and device LED will be ON. Keep
the status for about 5 seconds, release both keys and then LED will blink twice per second,
indicating that the Control is ready for programming.
3. Press and release
MUTE
key to enter automatic scan mode. And the remote will
automatically sending power codes to the device.
4. When the device turns ON, press
key to program the r
with the new code, saving
it and exit. To exit without programming, press any key other except
key.
5. If the device responds, no further programming is required. If the device does not respond,
repeat steps 1 through 4. And search will start from current code set.
6. After searching the entire data base, this mode will be automatically exited and led will blink
for 3 times.
Punch-Through Features
The remote provides two punch-through features that allow users to control TV volume and
DVD or VCR operation while the remote is in another device mode control certain features of
another device.
Volume Punch-Through:
The TV Volume/Mute punch-through feature allows you to control the volume and mute function
of your TV while the r
is in another device mode. The feature is applicable for all devices
and brands that do not use the volume control buttons for other purposes.
Transport Key Punch-Through:
The DVD or VCR transport key punch through feature lets you r
the PLAY, STOP, PAUSE,
REWIND, FF and RECORD functions of your DVD or VCR while the control operates in other
modes. The feature is applicable for all devices and brands that do not use the transport keys
for other purposes.
Protection mode
1. While press and holding
, press
FREEZE
key for 5 seconds to enter protection mode. In
this mode, all the above programming methods will be invalid.
2.To exit protection: While press and holding
, press
FREEZE
key. Current device related
LED remains ON and then release
and
FREEZE.
Input three digit password
8 8 8
, LED
turns off and protection mode is ended. If error password is input or no password input in 10
seconds, LED blinks three times and then turns off. Protection mode will remain.
Display mode
1.To enter display mode, while press and holding
key
,
press
SELECT
key and device
LED will be ON, keep the status for about 5 seconds. Release both keys and then LED will
blink 2 times per second, indicating r
is ready for programming.
2.Sequence press 9, 8, 0 to enter display mode. And LED is off now.
3.Press digit 1 key to get the first digit of current code set. For example, if the first digit of code
set is 1, so then led will blink once and remains OFF. Digit 0
in code set will not be displayed.
Blink twice per second.
4.Press digit 2 key to get the second digit of current code set. For example, if the second digit
of code set is 3, so then led will blink three times and remains OFF. Blink twice per second.
5.Press digit
3 key to get the third digit of current code set. Blink twice per second.
6.Only digit 1, 2, 3
are valid in this mode. And the sequence is not fixed. You can repeat, if you
don't remember clearly.
7.R
will not send out data in this mode if user presses any keys other than digit 1, 2, 3.
And this can be regarded as no key pressed.
8.If no key was pressed in 10 seconds or any key other than digit 1, 2, 3 is pressed
display
mode is ended.