HP 1606 HP StorageWorks B-series Data Center Fabric Manager Enterprise, Profes - Page 50

All Fabric and Chassis., All Fabrics

Get HP 1606 PDF manuals and user guides View all HP 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Closed fixes summary Solution In MEOS unassigning the threshold from "All Fabrics" does not unassign the policy assigned to the chassis group and VF Workaround prior to upgrade: While removing the policy at the All Fabric level if it is also removed from Chassis, the policy is removed from All Fabric and Chassis. Fixed in DCFM 10.4.0. In dual NIC PC the call home service is always showing the source address as Private IP even though the private IP is not selected during installation Fixed in DCFM 10.4.0. HBA Icon is not shown in topology when collapsing and expanding the host group after server port mapping. Fixed in DCFM 10.4.0. When an M model switch port is disabled, the Calculated Status is not updated from Healthy to Marginal in Port Properties. Fixed in DCFM 10.4.0. DCFM is not restricting when domain ID greater than 31 is added to the zone in Interopmode 2, which in turn cause the zone activation failure with inappropriate message. Workaround prior to upgrade: Do not add members with Domain ID greater than 31 in Interopmode 2. Fixed in DCFM 10.4.0. Nothing happened when clicking the buttons present in the FCIP Tunnel dialog box. Exception thrown in client log. Workaround prior to upgrade: Close and open the FCIP Tunnel dialog box and try the same operation. Fixed in DCFM 10.4.0. Actions panel in Add Event Policy dialog box is unusable if the length of the Name is more than 140 characters in the trigger section when Fixed in DCFM 10.4.0. policy is reopened for editing. Blank error message was shown in the Server Management Console when trying to test the valid Radius server user credentials. Fixed in DCFM 10.4.0. There is a mismatch in the Tunnel ID shown in the FCIP Tunnel dialog box and the Masterlog for the tunnels created between multiprotocol extension blades and the multiprotocol router blades and 400 multiprotocol switches. Fixed in DCFM 10.4.0. Failed to add VIP interface, error: Configuration entry exists on a GigE port error shown while clicking the Current Maximum Bandwidth button present in the Edit Circuit dialog box Fixed in DCFM 10.4.0. Yellow dash line is not displayed between 4/256 Director ghost and 400 multiprotocol router. Fixed in DCFM 10.4.0. Blank FCIP Tunnels dialog box opened when the switches are in Unmanageable state. Fixed in DCFM 10.4.0. Ambiguous Error message is displayed during firmware import to the repository when there is a low disk space. Fixed in DCFM 10.4.0. Topology is not shown with -ve symbol for switches and end devices which made offline during migration from DCFM 10.1.x to DCFM Fixed in DCFM 10.4.0. 10.3.0. 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Solution
Closed fixes summary
Workaround prior to upgrade:
While
removing the policy at the All Fabric
level if it is also removed from
Chassis, the policy is removed from
All Fabric and Chassis.
Fixed in DCFM 10.4.0.
In MEOS unassigning the threshold from
“
All Fabrics
”
does not unas-
sign the policy assigned to the chassis group and VF
Fixed in DCFM 10.4.0.
In dual NIC PC the call home service is always showing the source
address as Private IP even though the private IP is not selected during
installation
Fixed in DCFM 10.4.0.
HBA Icon is not shown in topology when collapsing and expanding
the host group after server port mapping.
Fixed in DCFM 10.4.0.
When an M model switch port is disabled, the Calculated Status is
not updated from Healthy to Marginal in Port Properties.
Workaround prior to upgrade:
Do not
add members with Domain ID greater
than 31 in Interopmode 2.
Fixed in DCFM 10.4.0.
DCFM is not restricting when domain ID greater than 31 is added to
the zone in Interopmode 2, which in turn cause the zone activation
failure with inappropriate message.
Workaround prior to upgrade:
Close
and open the FCIP Tunnel dialog box
and try the same operation.
Fixed in DCFM 10.4.0.
Nothing happened when clicking the buttons present in the FCIP Tunnel
dialog box. Exception thrown in client log.
Fixed in DCFM 10.4.0.
Actions panel in Add Event Policy dialog box is unusable if the length
of the Name is more than 140 characters in the trigger section when
policy is reopened for editing.
Fixed in DCFM 10.4.0.
Blank error message was shown in the Server Management Console
when trying to test the valid Radius server user credentials.
Fixed in DCFM 10.4.0.
There is a mismatch in the Tunnel ID shown in the FCIP Tunnel dialog
box and the Masterlog for the tunnels created between multiprotocol
extension blades and the multiprotocol router blades and 400 multi-
protocol switches.
Fixed in DCFM 10.4.0.
Failed to add VIP interface, error: Configuration
entry exists on a GigE port
error shown while clicking the
Current Maximum Bandwidth button present in the Edit Circuit dialog
box
Fixed in DCFM 10.4.0.
Yellow dash line is not displayed between 4/256 Director ghost and
400 multiprotocol router.
Fixed in DCFM 10.4.0.
Blank FCIP Tunnels dialog box opened when the switches are in Un-
manageable state.
Fixed in DCFM 10.4.0.
Ambiguous Error message is displayed during firmware import to the
repository when there is a low disk space.
Fixed in DCFM 10.4.0.
Topology is not shown with
-ve
symbol for switches and end devices
which made offline during migration from DCFM 10.1.x to DCFM
10.3.0.
50