HP Designjet 700 HP DesignJet 700 user guide - Page 49

Task 8: Con the Interface

Get HP Designjet 700 PDF manuals and user guides View all HP Designjet 700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

SETUP 1 Setting Up the Plotter Task 8: (Serial Interface Users Only) Configure the Interface Task 8: Configure the Interface (Serial Interface Users Only) The following table shows the settings available for the plotter's serial interface parameters, the factory defaults and the most likely requirements for different computers. Parameter Baud rate Parity(1) Serial (RS-232-C) Settings Available settings Likely requirement for ... PC Macintosh Unix 1200 2400 4800 9600 19200 38400 None Even Odd 9600 (2) None (2) 9600 None Italics = factory default (1) Parity of None = 8 data bits, 1 stop bit Parity of Even or Odd = 7 data bits, 1 stop bit (2) Consult your software documentation. The settings on the plotter must match those of the computer and software sending the data. Use their documentation to find the requirements. If in doubt, try with the above suggestions. If the plotter's defaults already match the requirements, then you can skip the rest of this task. 1-29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
1-29
Task 8: Configure the Interface
(Serial Interface Users
Only)
The following table shows the settings available for the plotter’s serial interface
parameters, the factory defaults and the most likely requirements for different
computers.
Serial (RS-232-C) Settings
Likely requirement for ...
Available
Likely requirement for ...
Parameter
Available
settings
PC
Macintosh
Unix
Baud rate
1200
2400
4800
9600
19200
38400
9600
(2)
9600
Parity
(1)
None
Even
Odd
None
(2)
None
Italics = factory default
(1)
Parity of None = 8 data bits, 1 stop bit
Parity of Even or Odd = 7 data bits, 1 stop bit
(2)
Consult your software documentation.
The settings on the plotter must match those of the computer and software sending
the data.
Use their documentation to find the requirements.
If in doubt, try with
the above suggestions.
If the plotter’s defaults already match the requirements,
then you can skip the rest of this task.
SETUP
1
Setting Up the Plotter
Task 8: (Serial Interface Users Only) Configure the Interface