Home » HP Manuals » Bridges & Routers » HP J9087A » Manual Viewer

HP J9087A User Manual - Page 86

Installing the Patch Cord

Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Switch Ports and Network Cables Rx Tx Switch Ports and Network Cables Mode Conditioning Patch Cord for Gigabit-LX Installing the Patch Cord As shown in the illustration below, connect the patch cord to the Gigabit-LX mini-GBIC with the section of single-mode fiber plugged in to the Tx (transmit) port. Then, connect the other end of the patch cord to your network cabling patch panel, or directly to the network multimode fiber. If you connect the patch cord directly to the network cabling, you may need to install a female-to-female adapter to allow the cables to be connected together. Gigabit-LX port To network multimode cabling Mode ConLdCitCioonninnegctor Patch Cord The multimode cable in the patch cord must match the characteristics of your network cable Single-mode section plugs into Tx port on Gigabit-LX Transceiver or Gigabit-LX mini-GBIC Make sure you purchase a patch cord that has LC connectors on the end that connects to the Gigabit-LX mini-GBIC, and has multimode fibers that match the characteristics of the multimode fiber in your network. B-4

Section	Page
Installation and Getting Started Guide for the ProCurve Series 2600 Switches	1
Title Page	3
Copyright and Disclaimer Notices	4
Contents	5
1.Introducing the Switch	9
Front of the Switch	11
Network Ports	12
LEDs	12
Port LEDs	14
Multiple-Display Port LEDs - Port LED View or LED Mode Select Button and Indicator LEDs	15
Reset Button	17
Clear Button	17
Back of the Switch	18
Console Port	19
Power Connector	19
Switch Features	19
2.Installing the Switch	21
Included Parts	21
Installation Procedures	23
Installation Precautions	24
1. Prepare the Installation Site	25
2. Installing or Removing mini-GBICs	27
3. Verify the Switch Passes Self Test	29
LED Behavior	30
4. Mount the Switch	31
Rack or Cabinet Mounting	31
Rack Mounting the 2626-PWR and 2650-PWR switches	32
Rack Mounting the Non-PWR Switches and the 2600-8-PWR Switch	34
Flat Wall Mounting	36
Wall mounting the Series 2600 Non-PWR Switches	37
Wall mounting the Series 2600-8-PWR Switch	38
Horizontal Surface Mounting	39
5. Connect the Switch to a Power Source	39
6. Connect the Network Cables	40
Using the RJ-45 Connectors	40
Connecting Cables to mini-GBICs	41
7. (Optional) Connect a Redundant Power Supply to a Series 2600-PWR Switch	41
RPS/EPS Operation	42
Operating Characteristics of the 600 RPS/EPS (J8168A)	42
600 RPS/EPS LEDs	43
610 EPS LEDs	47
Operating Characteristics of the 610 EPS (J8169A)	47
8. (Optional) Connect a Console to the Switch	50
Terminal Configuration	50
Direct Console Access	51
Sample Network Topologies for Non-PWR Switches	52
As a Desktop Switch	52
As a Segment Switch	53
Connecting to a Backbone Switch	55
Sample Network Topologies for PWR Switches	56
As a Desktop Switch Implementing PoE	56
As a Segment Switch Implementing PoE	57
Stacking the Switch	59
3.Configuring the Switch	61
Recommended Minimal Configuration	61
Using the Console Setup Screen	62
Where to Go From Here	64
Using the IP Address for Remote Switch Management	65
Starting a Telnet Session	65
Starting a Web Browser Session	65
4.Troubleshooting	67
Basic Troubleshooting Tips	67
Diagnosing with the LEDs	70
Proactive Networking	74
Hardware Diagnostic Tests	75
Testing the Switch by Resetting It	75
Checking the Switch LEDs	75
Checking Console Messages	75
Testing Twisted-Pair Cabling	76
Testing Switch-to-Device Network Communications	76
Testing End-to-End Network Communications	76
Restoring the Factory Default Configuration	77
Downloading New Switch Software	78
HP Customer Support Services	78
Before Calling Support	78
A.Switch Specifications	79
Physical	79
Electrical	79
Environmental	80
BTU Ratings	80
Acoustic	80
Connectors	81
Cable Length	81
Safety	81
Lasers	81
B.Switch Ports and Network Cables	83
Switch Ports	83
Twisted-Pair Cables	83
Fiber-Optic Cables	84
Mode Conditioning Patch Cord for Gigabit-LX	85
Installing the Patch Cord	86
Twisted-Pair Cable/Connector Pin-Outs	87
Straight-through Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connections	89
Cable Diagram	89
Pin Assignments	89
Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection	90
Cable Diagram	90
Pin Assignments	90
Straight-Through Twisted-Pair Cable for 1000 Mbps Network Connections	91
Cable Diagram	91
Pin Assignments	91
C.Safety and EMC Regulatory Statements	93
Safety Information	93
Informations concernant la sécurité	94
Hinweise zur Sicherheit	95
Considerazioni sulla sicurezza	96
Consideraciones sobre seguridad	97
Safety Information (Japan)	98
Safety Information (China)	99
EMC Regulatory Statements	100
U.S.A.	100
Canada	100
Australia/New Zealand	100
Japan	100
Korea	101
Taiwan	101
European Community	102
Waste Electrical and Electronic Equipment (WEEE) Statements	104
Index	109