HP LaserJet Pro M1536 HP LaserJet Pro M1530 - Software Technical Reference - Page 68

Units, Custom width and height control limits, Paper source:, Inches, Millimeters, Device Settings

Page 68 highlights

Any entry that is greater than the maximum limits of the width and height controls is rounded down to the maximum valid entry, while any entry that is smaller than the minimum limits of the width and height control is rounded up to the minimum valid entry. If units are in millimeters, the custom paper-size range minimum is the limit rounded up to the nearest whole millimeter. The custom paper-size range maximum is the limit rounded down to the nearest whole millimeter. Any non-numerical entry reverts to the last valid entry. Width and height entries are validated when the focus has changed. The resolution of each control is 1 millimeter or 1/10 of an inch, depending on the current measurement units. Units To change measurement units, click one of the options in the Units group box, either Inches or Millimeters. Custom width and height control limits The minimum paper size for the product is 76.2 x 127 mm (3 x 5 inches) and the maximum size is 215.9 x 355.6 mm (8.5 x 14 inches). The following table summarizes paper size limits for each paperhandling option. Table 4-1 HP PCL6 printer driver custom paper sizes Tray Dimensions Minimum Maximum Tray 1 Duplexing unit Width Length Width Height 76.2 mm (3 inches) 127.0 mm (5 inches) 76.2 mm (3 inches)) 127.0 mm (5 inches) 215.90 mm (8.5 inches) 355.6 mm (14.0 inches) 215.9 mm (8.5 inches) 355.6 mm (14.0 inches) Paper source: The Paper source: setting specifies the source tray or printing a document. The list of source trays depends on the installed product accessories. Any optional source trays that are installed through the Device Settings tab also appear here. The Paper source: drop-down menu can contain the following options, depending on what has been installed on the product: ● Automatically Select ● Printer auto select ● Manual Feed in Tray 1 ● Tray 1 The default setting is Automatically Select. When this setting is selected, the product uses the source tray that supports the selected paper size. If you select a source tray other than Automatically Select, make sure that the correct paper size is loaded in the source tray. 54 Chapter 4 HP PCL 6 and PCL 5 printer drivers for Windows ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118

Any entry that is greater than the maximum limits of the width and height controls is rounded down to
the maximum valid entry, while any entry that is smaller than the minimum limits of the width and
height control is rounded up to the minimum valid entry.
If units are in millimeters, the custom paper-size range minimum is the limit rounded up to the nearest
whole millimeter. The custom paper-size range maximum is the limit rounded down to the nearest
whole millimeter. Any non-numerical entry reverts to the last valid entry. Width and height entries are
validated when the focus has changed.
The resolution of each control is 1 millimeter or 1/10 of an inch, depending on the current
measurement units.
Units
To change measurement units, click one of the options in the
Units
group box, either
Inches
or
Millimeters
.
Custom width and height control limits
The minimum paper size for the product is 76.2 x 127 mm (3 x 5 inches) and the maximum size is
215.9 x 355.6 mm (8.5 x 14 inches). The following table summarizes paper size limits for each paper-
handling option.
Table 4-1
HP PCL6 printer driver custom paper sizes
Tray
Dimensions
Minimum
Maximum
Tray 1
Width
76.2 mm (3 inches)
215.90 mm (8.5 inches)
Length
127.0 mm (5 inches)
355.6 mm (14.0 inches)
Duplexing unit
Width
76.2 mm (3 inches))
215.9 mm (8.5 inches)
Height
127.0 mm (5 inches)
355.6 mm (14.0 inches)
Paper source:
The
Paper source:
setting specifies the source tray or printing a document. The list of source trays
depends on the installed product accessories. Any optional source trays that are installed through the
Device Settings
tab also appear here.
The
Paper source:
drop-down menu can contain the following options, depending on what has been
installed on the product:
Automatically Select
Printer auto select
Manual Feed in Tray 1
Tray 1
The default setting is
Automatically Select
. When this setting is selected, the product uses the
source tray that supports the selected paper size. If you select a source tray other than
Automatically Select
, make sure that the correct paper size is loaded in the source tray.
54
Chapter 4
HP PCL 6 and PCL 5 printer drivers for Windows
ENWW