HP Point of Sale rp5000 Hardware Reference Guide (2nd Edition) - Page 48

black. HP-supplied standard screws are silver.

Get HP Point of Sale rp5000 PDF manuals and user guides View all HP Point of Sale rp5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Hard Drive Installation Guidelines ■ 80-conductor Ultra ATA cable: ❏ 18 inches maximum total length, 80-conductor cable with maximum spacing of 6 inches between Device 0 and Device 1. 80-Conductor Ultra ATA Cable 1 Device 0 (master drive) connector 2 Device 1 (slave drive) connector 3 System board connector ■ For optimal performance, connect hard drives to the primary controller. Connect expansion devices, such as ATA optical drives, tape drives, and diskette drives, to the secondary controller. ■ Install either a third-height or a half-height drive into a half-height bay. ■ Install guide screws to ensure that the drive lines up correctly in the drive cage. HP has provided extra guide screws installed in the front of the computer chassis behind the front bezel. Some options use M3 metric hardware. HP-supplied metric screws are black. HP-supplied standard screws are silver. ■ If only one device is connected to a cable, that device must be attached to the end (Device 0) connector. ✎ If you have only one device, make sure to connect it to the Device 0 connector. If you connect it to the Device 1 connector, the system will not recognize the device and you may get a "no fixed disk found" error message. C-2 www.hp.com Hardware Reference Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
C-2
www.hp.com
Hardware Reference Guide
Hard Drive Installation Guidelines
■
80-conductor Ultra ATA cable:
❏
18 inches maximum total length, 80-conductor cable with
maximum spacing of 6 inches between Device 0 and
Device 1.
80-Conductor Ultra ATA Cable
■
For optimal performance, connect hard drives to the primary
controller. Connect expansion devices, such as ATA optical
drives, tape drives, and diskette drives, to the secondary
controller.
■
Install either a third-height or a half-height drive into a
half-height bay.
■
Install guide screws to ensure that the drive lines up correctly in
the drive cage. HP has provided extra guide screws installed in
the front of the computer chassis behind the front bezel. Some
options use M3 metric hardware. HP-supplied metric screws are
black. HP-supplied standard screws are silver.
■
If only one device is connected to a cable, that device must be
attached to the end (Device 0) connector.
✎
If you have only one device, make sure to connect it to the Device 0
connector. If you connect it to the Device 1 connector, the system will
not recognize the device and you may get a “no fixed disk found”
error message.
1
Device 0 (master drive) connector
2
Device 1 (slave drive) connector
3
System board connector