HP StorageWorks 4000 Compaq StorageWorks Fibre Channel Troubleshooting Guide - Page 29

GigaBit Interface Converter Module-Shortwave, Fibre Channel Cable Option Kits

Get HP StorageWorks 4000 - RAID Array PDF manuals and user guides View all HP StorageWorks 4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Introduction 1-21 GigaBit Interface Converter Module-Shortwave This section contains information on the GigaBit Interface Converter Module-Shortwave. See page 1-10 of this guide. Fibre Channel Cable Option Kits This section contains information on the Fibre Channel Cable Option Kits. See page 1-11 of this guide. Replacing Components in a Secondary Storage System This section describes the steps required to replace devices connected to the Fibre Channel Arbitrated Loop (FC-AL). Replacing the Fibre Channel Host Bus Adapter WARNING: To reduce the risk of personal injury or damage to the equipment, refer to the documentation supplied with the RAID Array and observe the appropriate safety precautions and option installation instructions before following these procedures. When a Fibre Channel Host Bus Adapter fails, in a non PCI Hot Plug slot: 1. Perform a normal system shutdown of the server. 2. Power down the secondary storage components attached to the failed Fibre Channel Host Bus Adapter. 3. Remove the GBIC from the failed Fibre Channel Host Bus Adapter. 4. Remove the failed Fibre Channel Host Bus Adapter. 5. Install a new Fibre Channel Host Bus Adapter. 6. Install the GBIC that was removed in step 3, with the cable still attached. 7. Apply power to the secondary storage components. 8. Apply power to the server. When a Fibre Channel Host Bus Adapter/P fails in the PCI Hot Plug slot: 1. Power down the PCI Hot Plug slot. 2. Remove the Fibre Channel cable and GBIC from the failed Fibre Channel Host Bus Adapter. 3. Remove the failed Fibre Channel Host Bus Adapter. 4. Install the new Fibre Channel Host Bus Adapter. 5. Install the GBIC and Fibre Channel cable. 6. Power on the PCI Hot Plug slot.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Introduction
1-21
GigaBit Interface Converter Module-Shortwave
This section contains information on the GigaBit Interface Converter Module-Shortwave. See
page 1-10 of this guide.
Fibre Channel Cable Option Kits
This section contains information on the Fibre Channel Cable Option Kits. See page 1-11 of this
guide.
Replacing Components in a Secondary Storage
System
This section describes the steps required to replace devices connected to the Fibre Channel
Arbitrated Loop (FC-AL).
Replacing the Fibre Channel Host Bus Adapter
WARNING:
To reduce the risk of personal injury or damage to the equipment, refer to the
documentation supplied with the RAID Array and observe the appropriate safety precautions
and option installation instructions before following these procedures.
When a Fibre Channel Host Bus Adapter fails, in a non PCI Hot Plug slot:
1.
Perform a normal system shutdown of the server.
2.
Power down the secondary storage components attached to the failed Fibre Channel Host
Bus Adapter.
3.
Remove the GBIC from the failed Fibre Channel Host Bus Adapter.
4.
Remove the failed Fibre Channel Host Bus Adapter.
5.
Install a new Fibre Channel Host Bus Adapter.
6.
Install the GBIC that was removed in step 3, with the cable still attached.
7.
Apply power to the secondary storage components.
8.
Apply power to the server.
When a Fibre Channel Host Bus Adapter/P fails in the PCI Hot Plug slot:
1.
Power down the PCI Hot Plug slot.
2.
Remove the Fibre Channel cable and GBIC from the failed Fibre Channel Host Bus
Adapter.
3.
Remove the failed Fibre Channel Host Bus Adapter.
4.
Install the new Fibre Channel Host Bus Adapter.
5.
Install the GBIC and Fibre Channel cable.
6.
Power on the PCI Hot Plug slot.