HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 107

DDS-3 Tape Drive Optional, Removing a DDS-3 Tape Drive, Front Panel Screws, Replacing

Page 107 highlights

Field Replaceable Units (FRUs) FRU Removal and Replacement 9. Replace the EMI cover, the top panel, and front panel bezel. 10. After rebooting, use SAM to confirm that the CD ROM drive is recognized by the system. DDS-3 Tape Drive (Optional) This subsection describes how to remove and replace the optional DDS-3 tape drive. NOTE The bracket assembly and drive bay may be used for either one DDS-3 tape drive, or one floppy disk drive. Removing a DDS-3 Tape Drive: 1. Remove the front panel bezel from the workstation. 2. Remove the two T-15 Torx screws securing the DDS-3 tape drive to the front panel of the workstation chassis. Figure 4-12. Front Panel Screws T-15 Torx screw T-15 Torx screw 3. Slide the DDS-3 tape/floppy disk drive bracket assembly out of the chassis guide rails. Disconnect the the power and ribbon cables from the DDS-3 tape drive. 4. To remove the DDS-3 tape drive from the bracket, remove the four T-10 Torx screws (two on each side) securing the DDS-3 tape drive to the bracket. Replacing a DDS-3 Tape Drive: NOTE See "DDS-3 Tape Drive (Optional) Configuration" on page 38 for information about configuring a DDS-3 tape drive for installation. 1. Remove the front panel bezel and the top panel from the workstation. 2. In the top, left front of the workstation above the DDS-3/floppy disk drive bay, remove the EMI (electromagnetic interference) cover. Chapter 4 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214

Chapter 4
101
Field Replaceable Units (FRUs)
FRU Removal and Replacement
9.
Replace the EMI cover, the top panel, and front panel bezel.
10. After rebooting, use SAM to confirm that the CD ROM drive is recognized by the
system.
DDS-3 Tape Drive (Optional)
This subsection describes how to remove and replace the optional DDS-3 tape drive.
NOTE
The bracket assembly and drive bay may be used for either one DDS-3 tape
drive, or one floppy disk drive.
Removing a DDS-3 Tape Drive:
1.
Remove the front panel bezel from the workstation.
2.
Remove the two T-15 Torx screws securing the DDS-3 tape drive to the front panel of
the workstation chassis.
Figure 4-12. Front Panel Screws
3.
Slide the DDS-3 tape/floppy disk drive bracket assembly out of the chassis guide rails.
Disconnect the the power and ribbon cables from the DDS-3 tape drive.
4.
To remove the DDS-3 tape drive from the bracket, remove the four T-10 Torx screws
(two on each side) securing the DDS-3 tape drive to the bracket.
Replacing a DDS-3 Tape Drive:
NOTE
See “DDS-3 Tape Drive (Optional) Configuration” on page 38 for information
about configuring a DDS-3 tape drive for installation.
1.
Remove the front panel bezel and the top panel from the workstation.
2.
In the top, left front of the workstation above the DDS-3/floppy disk drive bay, remove
the EMI (electromagnetic interference) cover.
T-15 Torx screw
T-15 Torx screw