HP Visualize J5000 hp Visualize J5000, J7000 workstations service handbook (a4 - Page 121

Bus Bar Thumbscrews, Bus Bar Shield Installed

Page 121 highlights

Field Replaceable Units (FRUs) FRU Removal and Replacement 9. Secure the bus bars to the system board with either the four bus bar thumbscrews on the J5xxx workstation, or the five bus bar thumbscrews on the J7xxx. Figure 4-27 shows these thumbscrews on the J5xxx workstation. NOTE Failure to sufficiently tighten the bus bar thumbscrews will cause the power supply to not activate. Figure 4-27. Bus Bar Thumbscrews 10.Replace the bus bar shield by aligning the edge with the power supply edge while inserting the hooks into the slots. Rock the bus bar shield into place by pressing down towards the chassis floor. Figure 4-28 shows the bus bar shield correctly installed. Figure 4-28. Bus Bar Shield Installed Chapter 4 115

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214

Chapter 4
115
Field Replaceable Units (FRUs)
FRU Removal and Replacement
9.
Secure the bus bars to the system board with either the four bus bar thumbscrews on
the J5xxx workstation, or the five bus bar thumbscrews on the J7xxx. Figure 4-27
shows these thumbscrews on the J5xxx workstation.
NOTE
Failure to sufficiently tighten the bus bar thumbscrews will cause the power
supply to not activate.
Figure 4-27. Bus Bar Thumbscrews
10.Replace the bus bar shield by aligning the edge with the power supply edge while
inserting the hooks into the slots. Rock the bus bar shield into place by pressing down
towards the chassis floor. Figure 4-28 shows the bus bar shield correctly installed.
Figure 4-28. Bus Bar Shield Installed