Honeywell HJZTP User Manual - Page 26

Dome PTZ Protocol

Get Honeywell HJZTP PDF manuals and user guides View all Honeywell HJZTP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

3.3.3 Dome (PTZ) Protocol The keyboard can be set up to control RapidDome/Orbiter type domes using Honeywell VCL protocol or KD6/HD6 type domes using Honeywell Diamond protocol. Note: The protocol can only be set from the master keyboard. The protocol menu can be viewed on a slave keyboard, but 'AUX = SET' will not be displayed, and no selection will be allowed. To ensure slave keyboards have the correct protocol setting, they must be set as slave keyboards, and connected to the master keyboard, before editing the protocol on the master keyboard. Alternately entering and exiting the protocol menu on the master keyboard, or powering up the master keyboard will re-send the protocol setting to the slave keyboards. To set the dome protocol, select 'PRTCL' in the keyboard setup menu. The following menu will be displayed: AUX = SET P ROT OCOL L OCK = - VCL END Press 'aux' to toggle between 'VCL' and 'DIAMOND'. Once the required protocol has been selected, press 'lock' to exit the menu. Rev. 1.01 16 900.0570 8-Sept-05

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Rev. 1.01
16
900.0570
8-Sept-05
3.3.3
Dome (PTZ) Protocol
The keyboard can be set up to control RapidDome/Orbiter type domes using Honeywell
VCL protocol or KD6/HD6 type domes using Honeywell Diamond protocol.
Note:
The protocol can only be set from the master keyboard. The protocol menu can
be viewed on a slave keyboard, but ‘AUX = SET’ will not be displayed, and no selection
will be allowed. To ensure slave keyboards have the correct protocol setting, they must
be set as slave keyboards, and connected to the master keyboard, before editing the
protocol on the master keyboard. Alternately entering and exiting the protocol menu on
the master keyboard, or powering up the master keyboard will re-send the protocol
setting to the slave keyboards.
To set the dome protocol, select ‘
PRTCL’
in the keyboard setup menu. The following
menu will be displayed:
A
U
X
=
S
E
T
L
O
C
K
=
E
N
D
P
R
O
T
O
C
O
L
-
V
C
L
Press ‘aux’ to toggle between ‘
VCL
’ and ‘
DIAMOND
’. Once the required protocol has
been selected, press
‘lock’
to exit the menu.