Hoover S3630 Manual - Page 10
Agitator brush roll, replacement, Thermal protector, Lubrication, Service, Edge groomer, Headlight - vacuum
View all Hoover S3630 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
3 - 1 8 Agitator brush roll replacement When to replace Disconnect cleaner from electrical outlet. When agitator brush roll brushes are worn, the brush roll should be replaced. To check condition of brushes, move edge of a card across bottom plate while turning brush roll. To maintain cleaning effectiveness, replace brush roll if brushes do not touch card. Edge groomer replacement When to replace The edge groomers, located on both sides of the nozzle, should be replaced when they no longer extend past the surface of the bottom plate. What to buy When purchasing edge groomers, ask for Hoover part no. 39511004. How to replace Disconnect cleaner from electrical outlet. 1. Remove hood and b rush roll cover as shown in Figs. 3-9 to 3-12. 10 What to buy When purchasing a new agitator brush roll, ask for HOOVER part no. 48414-071. How to replace Disconnect cleaner from electrical outlet. 1. Remove hood, duct cover, belt and brush roll as shown in Figs. 3-9 to 3 - 1 4 . 2. Discard old brush roll. 3. Replace new brush roll and belt as shown in Figs. 3-15 to 3-17. Headlight replacem e n t The headlight, located on top of the power nozzle, operates when the cleaner is turned on. Use only HOOVER part no. 27317-307, which is a fused bulb, when replacing the headlight. How to replace Disconnect cleaner from electrical outlet and disconnect power nozzle from extension wands. 1. Remove the hood as shown in Figs. 3-9 and 3-10. 3 - 2 0 H G 2. Pull off both old edge groomers (G). 3.Push each new groomer onto the 3 tabs (H), starting with one of the end tabs. Then push the groomer onto the middle and remaining end tab. 4. Replace brush roll cover and hood as shown in Figs. 3-16 and 3-17. Lubrication The motor is equipped with two bearings that contain sufficient lubrication for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to either motor bearing. The agitator brush roll is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Service Center or an authorized Hoover Warranty Service Dealer (Depot). 3 - 1 9 2. Push old bulb into socket and twist to remove. Push new bulb into socket and twist into place. 3. Replace hood. Thermal protector An internal thermal protector has been used in your cleaner to prevent overheating if a large item or clog gets caught in the nozzle or at the opening of the bag. When the blockage is not removed, the thermal protector will trip and cleaner will stop running. If this happens, turn cleaner OFF and disconnect cleaner from electrical outlet. Then disconnect nozzle and remove obstruction. Within 15 minutes the thermal protector will cool and automatically reset and cleaning may resume. If cleaner does not operate, allow addi- tional time for thermal protector to reset. Service To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: • checking the Yellow Pages under "Vacuum Cleaners Household" OR • checking the list of Factory Service Centers provided with this cleaner OR • calling 1-800-944-9200 for an automated referral of authorized service outlet locations (U.S. only) O R • checking the Service section of The Hoover Company online at w w w. h o ov e rc o m p a ny. c o m Please do not send your cleaner to The Hoover Company in North Canton for service, this will only result in delay. If further assistance is needed, contact The Hoover Company Consumer Response Center, North Canton, Ohio 44720, Phone: 330-499-9499. In Canada, contact Hoover Canada, Burlington, Ontario L7R 4A8, Phone: 1-800-263-6376. Always identify your cleaner by the complete model number when requesting information or ordering parts. (The model number appears on the bottom of the cleaner.)