Husqvarna 130L Owner Manual - Page 13

To start a warm engine, WARNING, To start the engine when the fuel is, too hot, To stop the product

Get Husqvarna 130L PDF manuals and user guides View all Husqvarna 130L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

5. Push the choke control down to the half choke position in the center. electrical shock if the spark plug cap has been damaged. Do not use a product with a damaged spark plug cap. 6. Pull the starter rope handle until the engine starts. Note: If the engine does not start, do the start procedure from step 1. 7. Let the engine run for 10 seconds. 8. Push the choke control fully down to the no choke position. To start the engine when the fuel is too hot If the product does not start, the fuel can be too hot. Note: Always use new fuel and decrease the operation time during warm weather. 1. Put the product in a cool area away from open sunlight. 2. Let the product cool down for 20 minutes at minimum. 3. Press the air purge bulb again and again for 10-15 seconds. 4. Obey the procedure to start a cold engine. Refer to To start a cold engine on page 12. To stop the product • Push the stop switch to stop the engine. To start a warm engine 1. Move the choke lever to the FULL CHOKE position. 2. Move the choke lever to the HALF CHOKE position. 3. Pull the starter rope handle quickly until the engine runs. 4. Move the choke lever to the NO CHOKE position. About the surface WARNING: Do not put parts of your body in the grey marked area. If you touch the grey marked area it can result in burns to the skin. It can also cause Note: The stop switch automatically goes back to its initial position. 1687 - 003 - 22.09.2021 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
5.
Push the choke control down to the half choke
position in the center.
6.
Pull the starter rope handle until the engine
starts.
Note:
If the engine does not start, do the start
procedure from step 1.
7.
Let the engine run for 10 seconds.
8.
Push the choke control fully down to the no
choke position.
To start a warm engine
1.
Move the choke lever to the FULL CHOKE
position.
2.
Move the choke lever to the HALF CHOKE
position.
3.
Pull the starter rope handle quickly until the
engine runs.
4.
Move the choke lever to the NO CHOKE
position.
About the surface
WARNING:
Do not put parts of your
body in the grey marked area. If you
touch the grey marked area it can result
in burns to the skin. It can also cause
electrical shock if the spark plug cap has
been damaged. Do not use a product
with a damaged spark plug cap.
To start the engine when the fuel is
too hot
If the product does not start, the fuel can be too hot.
Note:
Always use new fuel and decrease the
operation time during warm weather.
1.
Put the product in a cool area away from open
sunlight.
2.
Let the product cool down for 20 minutes at
minimum.
3.
Press the air purge bulb again and again for
10-15 seconds.
4.
Obey the procedure to start a cold engine. Refer
to
To start a cold engine on page 12
.
To stop the product
•
Push the stop switch to stop the engine.
Note:
The stop switch automatically goes back to
its initial position.
1687 - 003 - 22.09.2021
13