Husqvarna 130L Owner Manual - Page 21

Troubleshooting

Page 21 highlights

Maintenance Clean the outside of the carburettor and the space around it. Do a check of the bevel gear to make sure that it is filled three-quarters with lubricant. Use special grease to fill if necessary. Clean or replace the spark arrestor mesh on the muffler (only applies to mufflers without a catalytic converter). Do a check of the fuel filter for contamination and the fuel hose for cracks or other defects (130L (LT13028CSHV). Replace if neccessary. Do a check of all cables and connections. Do a check of the clutch, clutch springs and the clutch drum for wear. Replace if neccessary by an authorized service workshop. Replace the spark plug. Make sure that the spark plug is fitted with a suppressor. Check and clean the spark arrestor mesh on the muffler (only applies to mufflers without a catalytic converter). Daily Weekly X Monthly X X X X X X X Troubleshooting The engine does not start Check Starter pawls. Fuel tank. Spark plug. Possible cause Procedure The starter pawls cannot move freely. Remove the starter cover and clean around the starter pawls. Let an approved service agent help you. Incorrect fuel type. Drain the fuel tank and fill with correct fuel. The spark plug is dirty or wet. Make sure that the spark plug is dry and clean. The spark plug electrode gap is incorrect. Clean the spark plug. Make sure that the electrode gap is correct. Make sure that the spark plug has a supressor. Refer to technical data for correct electrode gap. The spark plug is loose. Tighten the spark plug. The engine starts but stops again Check Fuel tank. Possible cause Incorrect fuel type. Procedure Empty the fuel tank and fill it with correct fuel. 1687 - 003 - 22.09.2021 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72

Maintenance
Daily
Weekly
Monthly
Clean the outside of the carburettor and the space around it.
X
Do a check of the bevel gear to make sure that it is filled three-quarters with
lubricant. Use special grease to fill if necessary.
X
Clean or replace the spark arrestor mesh on the muffler (only applies to
mufflers without a catalytic converter).
X
Do a check of the fuel filter for contamination and the fuel hose for cracks
or other defects (130L (LT13028CSHV). Replace if neccessary.
X
Do a check of all cables and connections.
X
Do a check of the clutch, clutch springs and the clutch drum for wear. Re-
place if neccessary by an authorized service workshop.
X
Replace the spark plug. Make sure that the spark plug is fitted with a sup-
pressor.
X
Check and clean the spark arrestor mesh on the muffler (only applies to
mufflers without a catalytic converter).
X
Troubleshooting
The engine does not start
Check
Possible cause
Procedure
Starter pawls.
The starter pawls cannot move freely.
Remove the starter cover and clean
around the starter pawls.
Let an approved service agent help you.
Fuel tank.
Incorrect fuel type.
Drain the fuel tank and fill with correct
fuel.
Spark plug.
The spark plug is dirty or wet.
Make sure that the spark plug is dry and
clean.
The spark plug electrode gap is incorrect.
Clean the spark plug. Make sure that the
electrode gap is correct. Make sure that
the spark plug has a supressor.
Refer to technical data for correct elec-
trode gap.
The spark plug is loose.
Tighten the spark plug.
The engine starts but stops again
Check
Possible cause
Procedure
Fuel tank.
Incorrect fuel type.
Empty the fuel tank and fill it with
correct fuel.
1687 - 003 - 22.09.2021
21