IBM 84903bu User Manual - Page 37

Installing, non-hot-swap, drive

Get IBM 84903bu - Servers X Series P4 3.4ghz PDF manuals and user guides
UPC - 000435882073
View all IBM 84903bu manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Installing a non-hot-swap SATA hard disk drive in bay 4, 5, 6, or 7 Some server models come with non-hot-swap SATA hard disk drives. Before you install a non-hot-swap SATA hard disk drive, read the following information: v Read the documentation that comes with the drive for cabling instructions. v Route the cable before you install non-hot-swap drives. Do not block the airflow from the fans. v You can install four non-hot-swap SATA hard disk drives in the server. v Install the drives in ascending order by bay number. Attention: Disconnect all power from the server before removing or installing a non-hot-swap hard disk drive. To install a non-hot-swap SATA hard disk drive, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 7. 2. Turn off the server and peripheral devices and disconnect all external cables and power cords. 3. Unlock the side cover (the bezel will not disengage from the server if the cover is locked). 4. Remove the side cover and lower bezel (see "Removing the side cover" on page 10 and "Removing the two-piece bezel" on page 11). 5. Touch the static-protective package that contains the drive to any unpainted metal surface on the server; then, remove the drive from the package and place it on a static-protective surface. 6. Align the drive assembly with the guide rails in the bay (the connector end of the drive goes in first). Chapter 2. Installing options 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Installing
a
non-hot-swap
SATA
hard
disk
drive
in
bay
4,
5,
6,
or
7
Some
server
models
come
with
non-hot-swap
SATA
hard
disk
drives.
Before
you
install
a
non-hot-swap
SATA
hard
disk
drive,
read
the
following
information:
v
Read
the
documentation
that
comes
with
the
drive
for
cabling
instructions.
v
Route
the
cable
before
you
install
non-hot-swap
drives.
Do
not
block
the
airflow
from
the
fans.
v
You
can
install
four
non-hot-swap
SATA
hard
disk
drives
in
the
server.
v
Install
the
drives
in
ascending
order
by
bay
number.
Attention:
Disconnect
all
power
from
the
server
before
removing
or
installing
a
non-hot-swap
hard
disk
drive.
To
install
a
non-hot-swap
SATA
hard
disk
drive,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
7.
2.
Turn
off
the
server
and
peripheral
devices
and
disconnect
all
external
cables
and
power
cords.
3.
Unlock
the
side
cover
(the
bezel
will
not
disengage
from
the
server
if
the
cover
is
locked).
4.
Remove
the
side
cover
and
lower
bezel
(see
“Removing
the
side
cover”
on
page
10
and
“Removing
the
two-piece
bezel”
on
page
11).
5.
Touch
the
static-protective
package
that
contains
the
drive
to
any
unpainted
metal
surface
on
the
server;
then,
remove
the
drive
from
the
package
and
place
it
on
a
static-protective
surface.
6.
Align
the
drive
assembly
with
the
guide
rails
in
the
bay
(the
connector
end
of
the
drive
goes
in
first).
Chapter
2.
Installing
options
23