IBM DBCA-204860 Hard Drive Specifications - Page 58

Drive Address Setting

Get IBM DBCA-204860 - Travelstar 4.8 GB Hard Drive PDF manuals and user guides View all IBM DBCA-204860 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

6.6 Drive Address Setting A jumper is available at the interface connector to determine the drive address. The set position of the jumper is as shown in Figure 36. Using Cable Selection, the drive address depends on the condition of pin 28 of the AT interface cable. In the case when pin 28 is ground or low, the drive is a Master. If pin 28 is open or high level, the drive is a Slave. Figure 36. Address setting by a jumper for DBCA-2xxxxx. 6.6.1 Default Setting The default setting of jumper at shipment is No Jumper (Master). 50 OEM Specifications of DBCA-2xxxxx 2.5 inch H D D

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
6.6
Drive Address Setting
A jumper is available at the interface connector to determine the drive address. The set position of the
jumper is as shown in Figure 36.
Using Cable Selection, the drive address depends on the condition of pin 28 of the AT interface cable. In the
case when pin 28 is ground or low, the drive is a Master. If pin 28 is open or high level, the drive is a Slave.
Figure 36. Address setting by a jumper for DBCA-2xxxxx.
6.6.1
Default Setting
The default setting of jumper at shipment is No Jumper (Master).
50
OEM Specifications of DBCA-2xxxxx 2.5 inch HDD