Icom ID-880H Instruction Manual

Icom ID-880H Manual

Get Icom ID-880H PDF manuals and user guides View all Icom ID-880H manuals
Add to My Manuals
Save this manual to your list of manuals

Icom ID-880H manual content summary:

  • Icom ID-880H | Instruction Manual - Page 1
    INSTRUCTION MANUAL VHF/UHF DIGITAL TRANSCEIVER ID-880H This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
  • Icom ID-880H | Instruction Manual - Page 2
    DV mode (digital voice + low-speed data communication) operation-ready - Text message and call sign exchange - Transmitting position data with a third-party GPS receiver M DR (D-STAR Repeater) mode and repeater list allow you to operate a D-STAR repeater simply M Switchable VHF and UHF transceiver M
  • Icom ID-880H | Instruction Manual - Page 3
    WARNING! NEVER cut the DC power cable between the DC plug and fuse holder with any radio equipment contain- ing a transmitter. During mobile operation, DO radio, because they can damage the transceiver's surfaces. USE Icom microphones only (supplied or optional). Other manufac- turers' microphones
  • Icom ID-880H | Instruction Manual - Page 4
    . iii SUPPLIED ACCESSORIES The following accessories are supplied with the transceiver. q DC power cable (3 m†; 9.8 ft 1 w Separation cable (3.4 m†; 11.2 ft 1 e Microphone (HM-133 1 r Fuse (20 A 1 t Microphone hanger 1 y Mounting screws, nuts and washers 1 set u Mobile mounting bracket
  • Icom ID-880H | Instruction Manual - Page 5
    N Repeater list 34 N Repeater list programming 35 13 N Changing a repeater list 40 14 N Clearing a repeater list 41 15 5 DV MODE OPERATION 42-72 N Digital mode operation 42 16 N Current call sign setting 42 N Receiving a D-STAR repeater 43 17 N Received call sign 44 18 N Copying
  • Icom ID-880H | Instruction Manual - Page 6
    68 N Low-speed data communication 70 N Other function in the DV mode 72 6 GPS/GPS-A OPERATION 73-86 N GPS operation 73 N GPS-A operation 86 7 MEMORY/CALL CHANNELS 87-99 N General description 87 N Selecting a memory channel 88 N Selecting a call channel 89 N Memory channel programming 90
  • Icom ID-880H | Instruction Manual - Page 7
    Microphone keys 153 N All reset 154 N Partial reset 154 N Data cloning 155 N Auto power OFF 157 N Time-out timer 157 N Packet operation 157 N Weather channel operation 162 14 MAINTENANCE 164-165 N Troubleshooting 164 N Fuse replacement 165 15
  • Icom ID-880H | Instruction Manual - Page 8
    QUICK REFERENCE GUIDE Installation D Precaution - magnets R CAUTION Magnets are used for the controller NEVER put the controller near a clock, television set (CRT type), magnetic compass or any magnetic/IC cards, credit cards, etc. The magnets may cause the products to malfunction or may erase the
  • Icom ID-880H | Instruction Manual - Page 9
    . • The supplied remote controller bracket and separation cable can be used for installation. • Optional OPC-440 MICROPHONE CABLE (5.0 m; 16.4 ft) and OPC-647 (2.5 m; 8.2 ft) are available to extend the microphone cable. • Optional OPC-441 SPEAKER CABLE (5.0 m; 16.4 ft) is available to extend
  • Icom ID-880H | Instruction Manual - Page 10
    position. Nut Spring washer Mounting bracket Flat washer D Microphone connection A microphone connector is available on the main unit front panel. Connect the supplied microphone connector as illus- trated below. Transceiver Microphone When using self-tapping screws 25° Mounting nut III
  • Icom ID-880H | Instruction Manual - Page 11
    QUICK REFERENCE QUICK REFERENCE GUIDE D Controller's attachment/detachment You can attach or detach the controller to/from the main unit as below. • Attach the controller ±
  • Icom ID-880H | Instruction Manual - Page 12
    QUICK REFERENCE GUIDE D Remote installation The supplied remote controller bracket is used for into your vehicle q Remove two screws and magnets from the remote controller. Magnet Remote controller FH: Flat head FH M2.6 × 6 mm CAUTION: NEVER use any other than the supplied screws (FH M2.6
  • Icom ID-880H | Instruction Manual - Page 13
    QUICK REFERENCE GUIDE QUICK REFERENCE D Battery connection ±
  • Icom ID-880H | Instruction Manual - Page 14
    QUICK REFERENCE GUIDE D Antenna installation • Antenna location To obtain maximum performance solder) 10 mm Soft solder 1-2 mm q Slide the coupling ring down. Strip the cable jacket and tin. w Strip the cable as shown at left. Soft solder the center conductor. solder solder e Slide the
  • Icom ID-880H | Instruction Manual - Page 15
    GUIDE Your first contact Now that you have your ID-880H powering up your ID-880H, you may want to make sure the audio volume and squelch ] for 1 sec. to reset the CPU. 2. Selecting the operating frequency band The ID-880H can use the 2 m or 144 MHz band Push • 400 MHz band Push VIII QUICK REFERENCE
  • Icom ID-880H | Instruction Manual - Page 16
    QUICK REFERENCE GUIDE 3. Tune the frequency The tuning dial will allow you to dial in the frequency you want to use. Page 15 will instruct you on how to set the tuning speed. [DIAL] Rotate [DIAL] to tune the frequency. Using the HM-133 You can directly enter the frequency
  • Icom ID-880H | Instruction Manual - Page 17
    QUICK REFERENCE QUICK REFERENCE GUIDE Repeater operation 1. Setting duplex ± Push [BAND] then rotate [DIAL] to select the frequency band. ± Push [BAND] again, then rotate [DIAL] to select the repeater frequency. ± Push and hold [DUP](LOW) for 1 sec. then rotate [DIAL] to select minus duplex or
  • Icom ID-880H | Instruction Manual - Page 18
    QUICK REFERENCE GUIDE Programming memory channels The ID-880H has a total of 1052 memory channels (including 25 MHz] to select the VFO. ± Rotate [DIAL] to set the desired frequency. • Set other data, such as repeater tone, duplex information, tuning step), if desired. 2. Selecting a memory channel
  • Icom ID-880H | Instruction Manual - Page 19
    q w er t Rear view y q ANTENNA CONNECTOR [ANT] (p. VII) Connects a 50 Ω antenna with a PL-259 connector and a 50 Ω coaxial cable for transmission and reception. w COOLING FAN Rotates while transmitting. Also rotates while receiving depending on the setting in the FUNC set mode (SET). (p. 129
  • Icom ID-880H | Instruction Manual - Page 20
    display (p. 4) q BAND MODE !4 VOL MENU S.MW w SQL VFO/MHz M/CALL DR CS LOW MONI MW e r t y u i o !0 !1 !2 !3 q MENU•LOCK KEY [MENU -99, 103) ± Push to enter the select memory write mode for memory channel programming. • Push [MENU ] to cancel and exit the select memory write mode. ±
  • Icom ID-880H | Instruction Manual - Page 21
    (p. III) Connects the supplied or an optional microphone. 13 q +8 V DC output t GND 14 i (Max. 10 mA) q w Channel up/down e 8 V control IN (microphone ground) y MIC (microphone input) 15 16 r PTT u GND i Data IN 17 !4 VOLUME CONTROL [VOL] (p. VIII) 18 Adjusts the audio level. 19 3
  • Icom ID-880H | Instruction Manual - Page 22
    !2 !1 !0 q o w i e Function guide (p. 6) r t y q TRANSMIT INDICATOR ± OUTPUT POWER INDICATORS (p. 18) "LOW" appears when low output power; "MID" appears GPS transmission or GPS-A transmission is selected in the DV mode. (p. 138) y BUSY INDICATOR ± Appears when a signal is being received
  • Icom ID-880H | Instruction Manual - Page 23
    STAR REPEATER) INDICATOR (pgs. 13, 50, 52) Appears when the DR mode is selected. !0 AUTO POWER OFF INDICATOR (p. 130) Appears when the auto power OFF function is in use. !1 GPS INDICATOR Appears when a GPS receiver is connected and a valid position data is received fied as a program skip frequency. !5
  • Icom ID-880H | Instruction Manual - Page 24
    functions. See page 2 to 3 (t to !0). • Set condition guides q wer VFO/MHz M/CALL DR CS LOW MONI Set condition guides appear when the transceiver enters the MENU screen, select memory write state, etc. q CLEAR KEY [CLR](DR) ± During programming state for call signs, repeater list, memory name
  • Icom ID-880H | Instruction Manual - Page 25
    DTMF sig- 12 nals can be transmitted with the keypad. u 2nd FUNCTION KEY [FUNC] 13 i DTMF SELECT KEY [DTMF-S] (p. 144) 14 o FUNCTION KEYS [F-1]/[F-2] (p. 153) 15 Program and recall your desired transceiver configuration. !0 BAND KEY [BAND] (p. 11) 16 Push to select the operating bands. 17
  • Icom ID-880H | Instruction Manual - Page 26
    Microphone 93) After pushing Transmits the DTMF code. : appropriate (pgs. 26, 144) When the DTMF memory en- Starts and stops scanning. (p. 107) Selects low output power. Selects minus duplex operation. Selects plus duplex operation. Selects simplex operation. Increases audio output level
  • Icom ID-880H | Instruction Manual - Page 27
    PANEL DESCRIPTION 1 1 KEY FUNCTION SECONDARY FUNCTION ( +key) OTHER FUNCTIONS 2 ±
  • Icom ID-880H | Instruction Manual - Page 28
    1 PANEL DESCRIPTION
  • Icom ID-880H | Instruction Manual - Page 29
    sec. to turn power ON or OFF. D Operating frequency band selection The ID-880H has 2 m and 70 cm bands for transmission and reception. In addition, that in this manual, sections beginning with a micro- 12 phone icon (as above), designate operation via the HM-133 microphone. 13 14 15 16 17 18
  • Icom ID-880H | Instruction Manual - Page 30
    What is VFO? VFO is an abbreviation of Variable Frequency Oscillator. Frequencies for both transmitting and receiving are generated and controlled by the VFO. [M/CALL] w Rotate [DIAL] to select the desired memory channel. • Only programmed memory channels can be selected. • See p. 90 for memory
  • Icom ID-880H | Instruction Manual - Page 31
    by the HM-133. x Push [ ] or [ ] to select the desired call channel. 1 D DR (D-STAR Repeater) mode 2 DR (D-STAR Repeater) mode is used for D-STAR repeater 3 operation. In this mode, you can select the pre-programmed repeaters and UR call sign easily. 4 q Push [DR] to select the DR mode
  • Icom ID-880H | Instruction Manual - Page 32
    the frequency. • If the VFO mode is not selected, push [VFO/MHz] to select the VFO mode. • The frequency changes in the selected tuning steps. (p. 15) w To change the frequency in 10 MHz (or 1 MHz) steps, push [VFO/MHz] once or twice, then rotate [DIAL]. Push [VFO/MHz] again. • Pushing and
  • Icom ID-880H | Instruction Manual - Page 33
    ] or push [Y]/[Z] on the microphone. 3 Independent tuning steps for 6.25 kHz* • 8.33 kHz† • 10 kHz • 12.5 kHz • 15 kHz* • 20 kHz • 25 kHz • 30 kHz • 50 kHz 6 • 100 200 kHz 7 *Not selectable in 900 MHz band. †Appears for VHF air band only. 8 NOTE: For convenience, select a tuning step
  • Icom ID-880H | Instruction Manual - Page 34
    . The transceiver has 2 different lock functions. D Frequency lock This function locks [DIAL] and keys electronically and can be used together with the microphone lock function. [MENU ] Appears ± Push and hold [MENU ] for 1 sec. to turn the lock function ON or OFF. • [PTT], [MONI] (monitor
  • Icom ID-880H | Instruction Manual - Page 35
    . 11 • DO NOT hold the microphone too close to your mouth or speak too loudly. This may distort the signal. 12 r Release [PTT] to return to receive. 13 IMPORTANT! (for 50 W transmission): 14 The ID-880H is equipped with protection circuits to protect 15 the power amplifier circuit from
  • Icom ID-880H | Instruction Manual - Page 36
    High: Mid: Low: POWER OUTPUT VHF/UHF Taiwan 50 W/50 W 25 W 15 W*/15 W* 15 W* 5 W*/5 W* 5 W* *approx. The microphone can also be used via the microphone MID during receive only. 5 LOW 6 18 Operating mode selection Operating modes are determined by the modulation of the radio signals.
  • Icom ID-880H | Instruction Manual - Page 37
    BASIC OPERATION 2 Squelch attenuator The transceiver has an RF attenuator related to the squelch level setting. Approx. 10 dB attenuation is obtained at maximum setting. The squelch attenuator allows you to set the minimum signal level needed to open the squelch. The attenuator function can be
  • Icom ID-880H | Instruction Manual - Page 38
    , deactivate the squelch attenuator function. See page 19 for details. Audio mute function This function temporarily mutes the audio without disturbing the volume setting. (microphone only) MUTE ± Push [FUNC] then [SQLY D(MUTE)] to mute audio signals. • Push [CLR A(MW)] (or any other key) to
  • Icom ID-880H | Instruction Manual - Page 39
    -touch PTT switch (each push toggles between transmit/receive). Using this function you can transmit without pushing and - ceive. • A beep sounds when transmission is started and a long beep sounds when returning to receive. c Push [FUNC] then [PRIO 3(PTT-M)] to turn the one-touch PTT function OFF.
  • Icom ID-880H | Instruction Manual - Page 40
    radio handbooks and local ham magazines for details of local repeaters such as repeater input/output frequencies and locations. Repeater example; Receives the 444.540 MHz signal and the detected audio • Some versions (USA/CHN/EXP/KOR) of the ID-880H have the auto repeater function. Thus the steps 3
  • Icom ID-880H | Instruction Manual - Page 41
    REPEATER OPERATION 3 Accessing a repeater q Set the receive frequency (repeater output frequency). (pgs. 14, 15) w Push and hold [DUP](LOW) for 1 sec. to enter the duplex setting condition. e Rotate [DIAL] to select minus duplex or plus duplex. • "DUP-" or "DUP" appears to indicate the transmit
  • Icom ID-880H | Instruction Manual - Page 42
    3 REPEATER OPERATION Accessing repeater (continued) DUP- 7 DUP+ 8 z Set the receive frequency (repeater output fre- quency). (pgs. 14, 15) x Push [DUP- 7(TONE)] to select minus duplex; push [DUP+ 8(TSQLS)] to select plus duplex. • "DUP-" or "DUP" appears. Push Push c Push [FUNC] then [DUP- 7(
  • Icom ID-880H | Instruction Manual - Page 43
    subaudible tones, such as the VFO mode or a memory/call channel. (Subaudible tone is available in FM/FM-N only.) • The subaudible tone frequency is independently programmed into each mode, band or channel. w Enter "R TONE" in the DUP.T menu.
  • Icom ID-880H | Instruction Manual - Page 44
    .  For your convenience! The transceiver has 16 DTMF memory channels for auto- patch operation. See p. 142 for details. D 1750 Hz tone The microphone has 1750 Hz tone capability, used for ring tone when calling, etc. z Push [FUNC]. TONE-1 • The function indicator lights orange. x Push [1(TONE
  • Icom ID-880H | Instruction Manual - Page 45
    through a repeater, the transmit frequency is shifted from the receive frequency by an amount determined by the frequency offset. Independent offset memory/ call channel. • The frequency offset is independently programmed into each mode, band or channel. w Enter "OFFSET" in the DUP.T menu.
  • Icom ID-880H | Instruction Manual - Page 46
    repeater tone frequencies are not changed by the auto repeater function. Reset these frequencies, if necessary. D Frequency range and offset direction • MHz "DUP-" appears • KOR version FREQUENCY RANGE 439.000-440.000 MHz SHIFT DIRECTION "DUP-" appears USA/CHN/EXP/KOR versions only q Enter "AUTORP"
  • Icom ID-880H | Instruction Manual - Page 47
    8 though they are thousands of miles apart! By using the gate- 9 way connection, long distance communication is possible using 144 or 440 MHz digital voice! 10 In the D-STAR system, an independent repeater's operating 11 area is called an Area and a group that of linked repeaters 12 via a 10
  • Icom ID-880H | Instruction Manual - Page 48
    4 DV MODE PROGRAMMING D System description Area 1 Repeater 1 Area 2 Zone A Repeater 2 Area 3 (Gateway) Repeater 3 range that is covered by a single repeater. The repeater is called an area repeater in the D-STAR system. Zone: The Zone is composed of several areas, that are linked by a 10 GHz
  • Icom ID-880H | Instruction Manual - Page 49
    60 call signs in the call sign memory. Up to 300 repeater call signs can be stored in the repeater list. D Your own call sign programming Your own call sign must be programmed for both digital voice and low-speed data communications (including GPS transmission). q Enter "MY" in call sign screen.
  • Icom ID-880H | Instruction Manual - Page 50
    i Push [ ](MONI) to store the programmed call sign with note and return to call sign screen. D Station call sign programming Station call sign must be programmed to call a specific station as well as for repeater operation in both digital voice and low-speed data communications. q Enter "UR" in call
  • Icom ID-880H | Instruction Manual - Page 51
    . to erase all characters following the cursor. y Push [ ](MONI) to store the programmed call sign and return to UR call sign screen. u Push [MENU ] to return to frequency indication.  For your information The ID-880H has a call sign edit record function. When editing a call sign stored in a call
  • Icom ID-880H | Instruction Manual - Page 52
    etc. In addition, they can be erased by malfunction and during repairs. Therefore, we recommend that memory data be written down or be saved to a PC using the CS-80/880 CLONING SOFTWARE (free download). RPT-L ADD-L q EDIT-L R-NAME e CALL S GW CAL GROUP R1 USE w Rpeater 1 NO YES ADD W R-NAME
  • Icom ID-880H | Instruction Manual - Page 53
    DV MODE PROGRAMMING 4 Repeater list programming D New repeater list programming q Enter "ADD-L" in RPT-L menu.
  • Icom ID-880H | Instruction Manual - Page 54
    is automatically added or replaced to "G." Repeater group programming (GROUP) The ID-880H has a total of 10 groups (0-9). You can [DIAL] to select the desired character, number, symbol ('/'only) or space. • Push [ ](LOW)/[ ](CS) to move the cursor right or left, respec- tively. • Call sign can be
  • Icom ID-880H | Instruction Manual - Page 55
    USE is selected YES. 2 !9 Push [ ](MONI) to enter the frequency programming state. 3 • Frequency programming screen is displayed. 4 5 6 @0 Rotate [DIAL] to select the frequency band. 7 • The selected number blinks at 1st digit. • Push [ ](LOW) to move the cursor right; push [ ](CS) to move
  • Icom ID-880H | Instruction Manual - Page 56
    PROGRAMMING Duplex direction setting (DUP) This content appears when R1 USE is selected YES. @4 Push [ ](MONI) to enter the duplex direction setting state. • Duplex direction setting screen is displayed. @9 Rotate [DIAL] to select the frequency offset. • The selected number blinks. • Push [ ](LOW
  • Icom ID-880H | Instruction Manual - Page 57
    programming state. • Repeater name programming screen is displayed. • The 1st digit blinks. w Rotate [DIAL] to select the desired character, number, symbol or space. • The selected character blinks. • Push [ ](LOW . 15 • Call sign can be up to 8 digits long. r Push [ ](MONI) to program the repeater
  • Icom ID-880H | Instruction Manual - Page 58
    is displayed. • Programmed repeater call sign is displayed, then the 1st char- acter blinks. • The 8th digit is automatically added or replaced to "G." w Rotate [DIAL] to select the desired character, number, symbol ('/' only) or space. • The selected character blinks. • Push [ ](LOW) to move the
  • Icom ID-880H | Instruction Manual - Page 59
    content to be changed, then push [ ](MONI) to enter the content and reprogram the content (see pages 35-38 for new repeater list programming details). y After programming is finished, rotate [DIAL] to select "ADD W" or "OVR W," then push [ ](MONI) to store to a new list or overwrite the selected list
  • Icom ID-880H | Instruction Manual - Page 60
    Digital mode operation The ID-880H can be operated in digital voice mode and lowspeed data operation for both transmit and receive. It can also be connected to a GPS receiver (compatible with an RS232 output/NMEA format/4800 bps/9600 bps) to transmit/receive position data. Current call sign setting
  • Icom ID-880H | Instruction Manual - Page 61
    to select the repeater call sign groups. e Push [CS] again to return to frequency indication. Receiving a D-STAR repeater 1 When the ID-880H receives a signal from a D-STAR repeater, 2 it receives four call signs: caller's call sign, called call sign, 3 repeater call sign 1 (the repeater that
  • Icom ID-880H | Instruction Manual - Page 62
    call sign When a call is received in the DV mode, the calling station and the repeater call signs being used can be stored into the received call record. The stored call signs are viewable in the following manner. Up to 20 calls can be recorded. D Desired call record indication q Enter RX
  • Icom ID-880H | Instruction Manual - Page 63
    record channel to current call sign. e Push [PTT] to transmit; release to receive. 1 Important! 2 Setting call signs with the "One-touch reply using the 135) is set to "AUTO," the repeater call sign in "RXRPT1" is stored as 15 "R2" and "RXRPT2" is stored as "R1" automatically. 16 NOTE: The One
  • Icom ID-880H | Instruction Manual - Page 64
    5 DV MODE OPERATION Copying the call sign D Copying the call sign memory contents This function is convenient when modifying a part of the current call sign. q Enter the call sign menu.
  • Icom ID-880H | Instruction Manual - Page 65
    DV MODE OPERATION 5 D Copying the call record contents into call sign memory 1 This is a way to copy the call record contents ("CALLER," "RXRPT1" and "RXRPT2") into call sign memory "UR" and repeater list "R-L" at the same time or individually. q Enter RX CAL (RX call sign) mode.
  • Icom ID-880H | Instruction Manual - Page 66
    STAR Repeater) mode operation DR (D-STAR Repeater) mode is used for D-STAR repeater operation. In this mode, you can select the pre-programmed the scan. • Scan pauses when a signal is received. • Rotate [DIAL] to change the scanning direction, or resumes manually. • Push [SCAN](VFO/MHz) to stop the
  • Icom ID-880H | Instruction Manual - Page 67
    • Skip setting Unwanted access repeater can be skipped for rapid selection or scan. q Enter "EDIT-L" in RPT-L menu.
  • Icom ID-880H | Instruction Manual - Page 68
    [DR] to enter the DR mode. Appears e Rotate [DIAL] to select the access repeater. • Only repeaters that have access repeater settings programmed are selectable. • Group indicator appears momentarily when rotating [DIAL]. • Access repeater scan can be used for the selection. (p. 48) [DR] Repeater
  • Icom ID-880H | Instruction Manual - Page 69
    call signɿ JA3YUA Repeater qɿNARA43 (JP3YHL) Continued instructions from step t on page 50. y Push . u Push [PTT] to transmit; release to receive. D Calling CQ in another area (Zone CQ/Different is set to the selected repeater automatically. 15 Calling CQ in another zone (Different zone
  • Icom ID-880H | Instruction Manual - Page 70
    ) q Push [DR] to enter DR mode. Appears e Rotate [DIAL] to select the access repeater. • Only repeaters that have access repeater settings programmed are selectable. • Group indicator appears momentarily when rotating [DIAL]. • Access repeater scan can be used for the selection. (p. 48) [DR
  • Icom ID-880H | Instruction Manual - Page 71
    ɿ Repeater qɿNARA43 JA3YUA JG3YMK (JP3YHL) Continued instructions from step t on page 52. STEP 3 selection. o Push [PTT] to transmit; release to receive. D Calling a specific station in the same zone Only repeaters that have programmed same gateway repeater appear. 15 16 17 18 i Push
  • Icom ID-880H | Instruction Manual - Page 72
    station in another zone (Different zone call) Continued instructions from step t on page 52. Zone A repeater "GW." • Only repeaters that have programmed same gateway repeater appear. Station call signɿ repeater at least once, the D-STAR system will connect to the repeater receive. 54
  • Icom ID-880H | Instruction Manual - Page 73
    signs that have programmed repeater names. r receive. 12 e Push [DR] to return to the previous setting. 13 • Push and hold [RX©CS](CS) also returns to the previous setting. 14 NOTE: If you want to save this temporary setting, push and hold [MW](S.MW) for 1 sec., then rotate [DIAL] to select 15
  • Icom ID-880H | Instruction Manual - Page 74
    in the VFO D Sending CQ q Set the desired frequency. (pgs. 14, 15) • Select output power, if desired. (p. 18) w Set the current MY [PTT] to return to receive. • The other station's call sign will be received. • Received call signs can be stored into the received call record automatically. See
  • Icom ID-880H | Instruction Manual - Page 75
    transmit and speak into the microphone at normal voice level. received call record automatically. See page 44 for details. 4 • Current call sign setting example (Simplex call) 5 6 Station call signɿ JG3YMK 7 My call signɿ JA3YUA 8 UR MY 9 10 11 R1: NOT USE R2: NOT USE 12 13 14 15
  • Icom ID-880H | Instruction Manual - Page 76
    ) q Set the desired repeater's frequency, offset and shift direction (pgs. 14, 15, 23, 27), then select the DV mode (p. 18). Your own call sign to return to frequency indication. t Push [PTT] to transmit; release to receive. • "CQCQCQ" is displayed and scrolled in sequence on the frequency display
  • Icom ID-880H | Instruction Manual - Page 77
    to return to frequency indication. 6 t Push [PTT] to transmit; release to receive. • UR call sign is displayed and scrolled in sequence on the fre- signɿ Station call signɿ Repeater qɿJP3YHL 12 JA3YUA JG3YMK 13 UR MY 14 15 R1 R2: (NOT USE) 16 17 18 19 Pushing and holding [BAND]
  • Icom ID-880H | Instruction Manual - Page 78
    q Set the desired repeater's frequency, offset and shift direction (pgs. 14, 15, 23, 27), then select the DV mode (p. 18). Your own call to return to frequency indication. t Push [PTT] to transmit; release to receive. • "CQCQCQ" is displayed and scrolled in sequence on the frequency display
  • Icom ID-880H | Instruction Manual - Page 79
    1 q Set the desired repeater's frequency, offset and shift direction (pgs. 14, 15, 23, 27), then select the DV mode (p. 18). Your own call sign ( to return to frequency indication. 6 t Push [PTT] to transmit; release to receive. • UR call sign is displayed and scrolled in sequence on the fre-
  • Icom ID-880H | Instruction Manual - Page 80
    q Set the desired repeater's frequency, offset and shift direction (pgs. 14, 15, 23, 27), then select the DV mode (p. 18). w Set the current to return to frequency indication. r Push [PTT] to transmit; release to receive. • UR call sign is displayed and scrolled in sequence on the frequency display
  • Icom ID-880H | Instruction Manual - Page 81
    1 q Set the desired repeater's frequency, offset and shift direction (pgs. 14, 15, 23, 27), then select the DV mode (p. 18). w Set the current MY to return to frequency indication. 4 r Push [PTT] to transmit; release to receive. • UR call sign is displayed and scrolled in sequence on the fre- 5
  • Icom ID-880H | Instruction Manual - Page 82
    5 DV MODE OPERATION Message operation D TX message programming TX messages are available for up to 5 channels and each channel can be programmed with a message of up to 20 characters. q Enter "TX MSG" in MESSAG (message) screen.
  • Icom ID-880H | Instruction Manual - Page 83
    You can toggle the message transmission function ON (TM1-TM5) and OFF. When a message channel is selected, the transceiver transmits a pre-programmed text message. (default: OFF) q Set the operating frequency, call signs and other settings, such as repeater operation, as desired. w Enter "TX
  • Icom ID-880H | Instruction Manual - Page 84
    5 DV MODE OPERATION D RX message indication The received message can also be checked in MESSAG (message) screen. q Select "RX MSG" in MESSAG (message) screen.
  • Icom ID-880H | Instruction Manual - Page 85
    available for digital mode operation. In the EMR communication mode, no call sign setting is necessary. When an EMR communication mode signal is received, the 3 "EMR" appears 4 audio (voice) will be heard at the specified level even if the volume setting level is set to minimum level, or digital
  • Icom ID-880H | Instruction Manual - Page 86
    two original stations are communicating with call sign squelch enabled. q While receiving an another station's communication, push and hold [RX©CS](CS) set the communicating station's call sign. • When a call sign has not been received correctly, error beeps sound and no call sign is set. Try to set
  • Icom ID-880H | Instruction Manual - Page 87
    5 However, when the call including the "BK ON" signal (break-in call) is received, the squelch will open and audio 6 sounds even if the call is specified for another station. 7 8 • Station C C is calling Station A. Station C Station C is calling Station A. Station C 15 16 17 18 19 69
  • Icom ID-880H | Instruction Manual - Page 88
    " (p. 56) and "D-STAR repeater operation in the VFO" (p. 58). w Follow the instructions for the data communication software. e To transmit data • At the same time as your voice audio, push and hold [PTT] to transmit while sending data from the PC. Release [PTT] to receive. • Under computer control
  • Icom ID-880H | Instruction Manual - Page 89
    D Transmission condition setting q Enter "DATATX" in the DV SET mode.
  • Icom ID-880H | Instruction Manual - Page 90
    DV mode D DV auto detect The "DV" mode indicator and "FM" mode indicator blink when a non-DV signal is received during DV mode operation. When a signal other than the DV mode is received, the ID880H DV automatic detection switches to monitor in the FM mode. q Enter "DV DET" in the DV SET mode.
  • Icom ID-880H | Instruction Manual - Page 91
    the GPS receiver 2 and DV* modes. You can also transmit GPS data when in DV mode. To receive GPS data, connect a third-party GPS re- 3 ceiver that has an RS-232C output and NMEA data format. 4 Third-party GPS receivers connect to the ID-880H [DATA] jack. 5 In addition, the GPS message
  • Icom ID-880H | Instruction Manual - Page 92
    6 GPS/GPS-A OPERATION D Sentence formatter setting q Enter "GPS-TX" in GPS mode.
  • Icom ID-880H | Instruction Manual - Page 93
    6 GPS/GPS-A OPERATION D GPS message programming q Enter "TX GPS" in MESSAG screen.
  • Icom ID-880H | Instruction Manual - Page 94
    6 GPS/GPS-A OPERATION D Received GPS message indication q Enter "RX GPS" in MESSAG screen.
  • Icom ID-880H | Instruction Manual - Page 95
    35°45.00'N 7 135°35.00'E 8 S/RF meter indicates 9 the selection 10 11 12 East or West 13 14 LOW Push CS Push MONI Push 15 16 Depending on the connected GPS receiver, "TIME" indica- 17 tion is not available. 18 These sample indications assume that "P FORM" is selected "mm.mm" and
  • Icom ID-880H | Instruction Manual - Page 96
    6 GPS/GPS-A OPERATION D Saving own/received position data q Enter "GPS.POS" in GPS mode.
  • Icom ID-880H | Instruction Manual - Page 97
    • Direction indication example NNW (N-- --) N (NW--) NW NNE NE (NE--) WNW ENE (W-- --) W E (E-- --) WSW ESE (SW--) SW SSW S (S-- --) SE (SE--) SSE 6 GPS/GPS-A OPERATION 1 2 MY 3 4 5 6 RX 7 8 9 10 GPS.M 11 12 13 14 15 16 17 18 19 79
  • Icom ID-880H | Instruction Manual - Page 98
    6 GPS/GPS-A OPERATION D GPS data addition q Enter "GPS.MEM" (GPS memory) in GPS mode.
  • Icom ID-880H | Instruction Manual - Page 99
    6 GPS/GPS-A OPERATION D GPS alarm setting GPS alarm sounds when your own position is close the specified position. This function can be set to use information from the received channel, a specified GPS memory channel or all GPS memory channels. q Enter "ALM-CH" in GPS mode.
  • Icom ID-880H | Instruction Manual - Page 100
    6 GPS/GPS-A OPERATION D GPS alarm setting in GPS memory channel GPS alarm setting for a specified GPS memory channel is available on GPS memory channel indication. q Enter "GPS.MEM" in GPS mode.
  • Icom ID-880H | Instruction Manual - Page 101
    6 GPS/GPS-A OPERATION D GPS memory clearing • Clear all memory channels q Enter "GPS.MEM" in GPS set mode.
  • Icom ID-880H | Instruction Manual - Page 102
    6 GPS/GPS-A OPERATION D Alarm area 1 Sets GPS alarm active range from 00.08′ to 59.99′ in 00.01′ steps. (default: 00.25′) q Enter "ALM1" in GPS set mode.
  • Icom ID-880H | Instruction Manual - Page 103
    6 GPS/GPS-A OPERATION D Alarm area 2 Selects GPS alarm active range from "BOTH," "EXTEND" and "LIMIT" when "CH" or "RX" is selected at GPS alarm setting. q Enter "ALM2" in GPS mode.
  • Icom ID-880H | Instruction Manual - Page 104
    ID-880H. GPS-A code is based on APRS® code. (APRS® : Automatic Position Reporting System) • GPS-A code details Your own call sign Unproto address Time stamp Time stamp h; H.M.S (Hour/Minute/Second) z; D.H.M (Day/Hour/Minute) Latitude Longitude Data extension Comment JA3YUA-1>API880,DSTAR
  • Icom ID-880H | Instruction Manual - Page 105
    Memory channel contents The following information can be programmed into memory channels: • Operating frequency (pgs. 14, 15) • Operating mode (p. 18) • Duplex data be written down or be saved to a PC using the CS-80/880 CLONING 6 SOFTWARE (free download software). 7 8 9 10 11 12 13 14 15
  • Icom ID-880H | Instruction Manual - Page 106
    dial q Push [M/CALL] several times to select the memory mode. • "X" indicator appears. w Rotate [DIAL] to select the desired memory channel. • Only programmed memory channels can be selected. Appears [DIAL] [M/CALL] D Using the [Y]/[Z] keys z Push [MR/CALL] to select the memory MR/CALL mode
  • Icom ID-880H | Instruction Manual - Page 107
    Selecting a call channel Call channel is a pre-programmed memory channel that can be accessed by simply pushing call channel button. ± Push [M/CALL] several times to select mode, or push [VFO/LOCK] to select the VFO mode. 7 MEMORY/CALL CHANNELS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 89
  • Icom ID-880H | Instruction Manual - Page 108
    7 MEMORY/CALL CHANNELS Memory channel programming q Push [VFO/MHz] to select the VFO mode. w Set the desired frequency: ± Select the desired band with [BAND]. ± Set the desired frequency with [DIAL]. ± Set other data (e.g. frequency offset, duplex direction, tone squelch, current call signs, etc.),
  • Icom ID-880H | Instruction Manual - Page 109
    channel via the microphone 1 The microphone can also be used to program memMW ory channels. 2 3 z Set the desired frequency in the VFO mode. ± Push [VFO/LOCK] to select the VFO mode. ± Push [ENT C(T-OFF)], then set the frequency using the keypad. ± Set other data (e.g. frequency offset, duplex
  • Icom ID-880H | Instruction Manual - Page 110
    7 MEMORY/CALL CHANNELS Memory bank setting The ID-880H has a total of 26 banks (A to Z). Regular memory bank. t Rotate [DIAL] to select the desired bank group from "A" to "Z." [DIAL] y Push [ ](LOW) to select the bank channel digit, then rotate [DIAL] to select the bank channel number from "00" to
  • Icom ID-880H | Instruction Manual - Page 111
    10 c Push [Y]/[Z] to select the desired bank, A to 2/3 Z. 11 • Only programmed memory bank can be selected. 12 v Push [CLR A(MW)] to set the bank. 14 the bank. n To return to regular memory condition, push 15 [FUNC], [MONI 1(BANK)] then push [Z] several times to select memory channel number
  • Icom ID-880H | Instruction Manual - Page 112
    (SET). (p. 132) q Push [M/CALL] to select the memory mode. • To program a call channel name, push [M/CALL] to select the call channel mode. w Rotate DIAL] to select the desired character. • The selected character blinks. • Push [ ](LOW) to move the cursor right; push [ ](CS) to move the cursor left.
  • Icom ID-880H | Instruction Manual - Page 113
    [DIAL] and [ ]. Push [ ], then rotete [DIAL] to select "M NAME." Push [ ], then push and hold [MW] for 1 sec. to program. Push [ ]. Select "B NAME*1" or "S NAME*2" when programming the bank name or the scan name, respectively. *1 B NAME can be set for bank assigned channels only. *2 S NAME can
  • Icom ID-880H | Instruction Manual - Page 114
    7 MEMORY/CALL CHANNELS Copying memory/call contents This function copies a memory channel's contents to the VFO (or another memory/call channel). This is useful when searching for signals around a memory channel frequency and for recalling the frequency offset, subaudible tone frequency etc. D
  • Icom ID-880H | Instruction Manual - Page 115
    to the target channel. • The targeted memory and copied contents are indicated. [EXAMPLE]: Copying memory channel 11 contents to channel 15. [DIAL] Select a memory channel, then push [S.MW]. Rotate [DIAL] to select a target channel. [S.MW ] 1 2 3 4 5 6 7 8 9 10 11 12 13 14
  • Icom ID-880H | Instruction Manual - Page 116
    7 MEMORY/CALL CHANNELS Memory clearing Contents of programmed memories can be cleared (erased), if desired. q Push [S.MW] to enter the select memory write mode. • "X" indicator and the memory channel number blink. • Do not
  • Icom ID-880H | Instruction Manual - Page 117
    cleared, the memory channel contents still remain programmed. e Push [ ](MONI) to channel stops blinking. [DIAL] [BAND] r Push [ ](LOW) to select the bank channels selection, or 6 push copied to the VFO. 13 Bank channel is displayed. 14 To erase. 15 [DIAL] [] [][ ] 16 [S.MW ] [CLR] 17 "- -
  • Icom ID-880H | Instruction Manual - Page 118
    SCAN (p. 102) Band Scan edges Band edge xxA xxB edge Scan Jump Repeatedly scans between two user-programmed frequencies. Used for checking for frequencies within a specified range such as repeater output frequencies, etc. FREQUENCY/MEMORY SKIP FUNCTION (p. 108) Band edge Band edge
  • Icom ID-880H | Instruction Manual - Page 119
    . BANK-LINK SCAN (pgs. 106, 124) Repeatedly scans bank channels selected at BANK-LINK items in the SCAN menu screen. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 101
  • Icom ID-880H | Instruction Manual - Page 120
    [SCAN] for 1 sec., then rotate [DIAL]. Programmed link scan Band scan Selectable from "0" to "9." Programmed scan Selectable from "0" to "24" if programmed. 102 t Push [SCAN](VFO/MHz) to start the scan. • Scan pauses when a signal is received. • Rotate [DIAL] to change the scanning direction
  • Icom ID-880H | Instruction Manual - Page 121
    the desired frequency: ± Select the desired band with [BAND]. ± Set the desired frequency with [DIAL]. ± Program different frequencies in "11A" and "11B" re- spectively. ± Set other data (e.g. frequency offset, duplex direction, tone squelch, etc.), if desired. e Push [S.MW](MW) to enter the select
  • Icom ID-880H | Instruction Manual - Page 122
    8 SCAN OPERATION D Programming scan edges via the microphone z Push [MR/CALL] to select the memory mode. MW x Select scan edge channel, 0A to 24A using [Y]/[Z] or keypad. • Push [ENT C(T-OFF)] then push only 1
  • Icom ID-880H | Instruction Manual - Page 123
    ](VFO/MHz) to start the scan. • Scan pauses when a signal is received. • Rotate [DIAL] to change the scanning direction. This also causes the transceiver function: Repeatedly scans all memory channels programmed with any frequencies of the band programmed in the memory channel selected for scanning
  • Icom ID-880H | Instruction Manual - Page 124
    SCAN](VFO/MHz) to start the scan. • Scan pauses when a signal is received. • Rotate [DIAL] to change the scanning direction. This also causes the 1 sec.,then rotate [DIAL]. Bank scan Selectable from "A" to "Z" if programmed. Duplex scan The bank-link setting can be changed in the SCAN set mode
  • Icom ID-880H | Instruction Manual - Page 125
    D Scan start/stop via the microphone z Push [VFO/LOCK] to select the VFO mode for SCAN full/band/programmed scan; push [MR/CALL] to 2 select the memory mode for memory scan. • Push [FUNC] + to start the scan. c Push [Y]/[Z] to stop the scan. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 107
  • Icom ID-880H | Instruction Manual - Page 126
    "SKIP," "PSKIP" or "OFF" for the selected channel. • PSKIP : The channel is skipped during memory/bank scan and the programmed frequency is skipped during VFO scan, such as programmed scan. • SKIP : The channel is skipped during memory or bank scan. • OFF : The channel is scanned during any scan
  • Icom ID-880H | Instruction Manual - Page 127
    SCAN OPERATION 8 Scan resume condition D Scan pause timer The scan pauses when receiving signals according to the scan pause time. It can be set from 2 to 20 sec. or unlimited. q Enter "PAUSE" in the SCAN set mode.
  • Icom ID-880H | Instruction Manual - Page 128
    8 SCAN OPERATION Skip channel/frequency setting (continued) D Setting Pause timer via the microphone z Push [BAND] to select the desired band. SET x Enter "PAUSE" in the SCAN set mode. B
  • Icom ID-880H | Instruction Manual - Page 129
    automatically selects the tone squelch function when priority watch starts. D About priority beep function When receiving a signal on the priority frequency, you can be alerted with beeps and a blink priority watch. 5 sec. DR mode VFO frequency 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 111
  • Icom ID-880H | Instruction Manual - Page 130
    9 PRIORITY WATCH Priority watch operation D Memory/call channel and memory scan watch q Select the VFO mode; then, set an operating frequency. w Select the channel(s) to be watched. For memory channel watch: Select the desired memory channel. For call channel watch: Select the desired call channel.
  • Icom ID-880H | Instruction Manual - Page 131
    PRIORITY WATCH 9 D VFO scan watch q Select the channel(s) to be watched. For memory channel watch: Select the desired memory channel. For call channel watch: Select the desired call channel. For memory scan watch: ± Select the memory mode, or the desired bank group. ± Push and hold [SCAN](VFO/MHz)
  • Icom ID-880H | Instruction Manual - Page 132
    resumes according to the selected scan resume condition. (p. 109) • To resume the watch manually when paused, push [PRIO 3(PTT-M)]. v To stop the watch, push [CLR A(MW)]. 114 D VFO scan watch via the microphone z Select the VFO mode; then, set the desired frePRIO quency. 3 x Set the watched
  • Icom ID-880H | Instruction Manual - Page 133
    PRIORITY WATCH 9 D VFO scan watch via the microphone (Continued) n Push [SCAN 2(T-SCAN)] to start the VFO scan PRIO watch. 3 • The transceiver checks the memory/bank channel(s) or call channel every 5 sec. • The watch
  • Icom ID-880H | Instruction Manual - Page 134
    used for programming infrequently changed "SET," "DV SET," "CALL-S," "RX CAL," "MESSAG," "RPT-L" or "GPS" appears. w Rotate [DIAL] to select "SET," then push [ ](MONI).* • before enter- ing the MENU screen. *[ ](MONI) ↔ [BAND] or [≈](LOW) Rotate [DIAL] Push [ ](MONI) [DIAL] [ ](MONI) Rotate [DIAL
  • Icom ID-880H | Instruction Manual - Page 135
    microphone The microphone can also be used to set the MENU SET screen settings. B z Push [SET B(D-OFF)]to enter the MENU screen. • One of "TS," "DUP.T," "SCAN," "SET," "DV SET," "CALL-S," "RX CAL," "MESSAG," "RPT-L" or "GPS Push Push Push Push 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 117
  • Icom ID-880H | Instruction Manual - Page 136
    MENU screen shows one of the following indication. • TS mode Setting (see p. 15) • DV SET mode • DUP.T mode Independent items (see p. 121) • mode • RPT-L mode - SOUNDS mode Independent items (see p. 132) • GPS mode 118 Independent items (see p. 134) Independent items (see p. 31)
  • Icom ID-880H | Instruction Manual - Page 137
    10 Items list 1 D TS mode D SET mode 2 See page 15 for details. 3 - FUNC mode - SOUNDS mode D DUP.T mode Item Ref. p. 130 p. 131 p. 130 p. 132 p. 134 p. 134 p. 135 p. 136 14 p. 136 15 p. 136 16 p. 123 p. 131 p. 132 p. 135 p. 137 17 p. 131 p. 135 p. 137 18 p. 135 19
  • Icom ID-880H | Instruction Manual - Page 138
    for details. D MESSAG mode Item indication Ref. Item indication Ref. p. 64 p. 75 p. 66 p. 76 D RPT-L mode Item indication Ref. Item indication Ref. p. 35 p. 40 D GPS mode Item indication Ref. Item indication Ref. p. 138 p. 84 p. 76 p. 85 p. 78 p. 138 p. 80 p. 141 p. 81
  • Icom ID-880H | Instruction Manual - Page 139
    .8 250.3 254.1 The transceiver has 50 tone frequencies and consequently their spacing is narrow compared with units having 38 tones. Therefore, some tone frequencies may receive interference from adjacent tone frequencies. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 121
  • Icom ID-880H | Instruction Manual - Page 140
    "TR-RN" (TX: reverse, RX: normal) and "BOTH R" (TX/RX: reverse). (default: BOTH N) This item allows you to set the transmit and receive DTCS code polarities independently. D DTMF speed Select the desired DTMF transmission speed from 100 msec, 200 msec, 300 msec, 500 msec. • 100 : 100 msec
  • Icom ID-880H | Instruction Manual - Page 141
    pauses for 2-20 sec. on a received signal in 2 sec. steps. (default: 10 sec.) • HOLD : Scan pauses on a received signal until it disappears. 1 D Scan function. 13 D Program skip scan 14 Sets programmed skip scan function ON (default) and OFF 15 for VFO scan (full scan, programmed scan, etc.)
  • Icom ID-880H | Instruction Manual - Page 142
    10 MENU SCREEN OPERATION D Weather alert USA/CHN/EXP versions only Turns weather alert function ON or OFF. (p. 162) (default: OFF) D Memory bank link function Sets the memory bank link function ON or OFF (default). The link function provides continuous bank scan, scanning all contents in the
  • Icom ID-880H | Instruction Manual - Page 143
    Confirming program scan link q Rotate [DIAL] to select the program scan link number that you want to confirm. w Push [ ](MONI) to enter program scan link to enter the name programming state. 7 8 9 10 t Rotate [DIAL] to select the desired character, number, symbol or space; push [ ](LOW) or [ ](CS
  • Icom ID-880H | Instruction Manual - Page 144
    scan number to be linked. r Push [ ](MONI) then rotate [DIAL] to select the desired programmed scan number to be deleted from the link. • Only programmed scan numbers that have not linked in the selected program link number are displayed. • Push [Ω](CS) to cancel the selection. t Push [ ](MONI) to
  • Icom ID-880H | Instruction Manual - Page 145
    2 Selects the microphone sensitivity from HIGH and LOW to 3 suit your preference. 4 (default : USA version; LOW, Other versions; microphone gain automati- 10 cally when the transmission audio is distorted. This function 11 is available in the FM/FM-N mode only. 12 13 14 D PTT lock 15
  • Icom ID-880H | Instruction Manual - Page 146
    OFF. This function inhibits transmission while receiving a signal or when the squelch function cuts transmission OFF after 1, 3, 5, 10, 15 or 30 min. of continuous transmis- sion. This are not changed by the auto repeater function. Reset these frequencies, if necessary. USA/CHN/EXP versions
  • Icom ID-880H | Instruction Manual - Page 147
    FAST, MID and SLOW. • SLOW : The fan continuously rotates at low speed. • MID : The fan continuously rotates at medium speed. • [S.MW MW]) 8 M/CALL (as [M/CALL]) DR (as [DR]) 9 CS (as [CS]) LOW (as [LOW]) 10 MONI (as [MONI]) 11 *Available for "MIC-UP" only; †Available for "MIC-DN" only
  • Icom ID-880H | Instruction Manual - Page 148
    4800 bps and 9600 bps (default) for low-speed data communication in the DV mode or GPS receiving. SET mode - DISP items D Display dimmer Sets backlighting brightness. The levels 1 (dark) to 4 (bright: default) are available. This setting does not change the cloning speed. D Auto power OFF The
  • Icom ID-880H | Instruction Manual - Page 149
    selected from 9 levels. • 1 (Low contrast) to 9 (High contrast) (default programmed. (default) 7 • BANK : The bank name, that the selected memory 8 channel is assigned to, is displayed. However, the programmed frequency is dis- 9 played if no bank name is programmed. 10 11 12 13 14 15
  • Icom ID-880H | Instruction Manual - Page 150
    received, selects a narrow audio filter width to reduce noise audio. (default) • F1 : The widest audio filter width. • F2 : Middle audio filter width. • F3 : The narrowest audio filter width. D Opening message The opening message indication that is displayed at power ON is selectable from "ICOM
  • Icom ID-880H | Instruction Manual - Page 151
    . (default: OFF) 1 D Standby beep 2 3 Turns the beep emission capability ON or OFF when the communicating station finishes transmitting or the receive 4 signal disappears during DV mode operation. (default: ON) 5 6 7 8 D Band edge beep 9 Turns the beep emission capability ON or OFF when
  • Icom ID-880H | Instruction Manual - Page 152
    received signal. (default) • DIGI : Monitors in the DV mode. • ANALOG : Monitors in the FM mode. D DV data TX During low-speed data operation, auto data transmission function is available. This function activates to transmit automatically when the PC software sends data to the ID-880H via the [DATA
  • Icom ID-880H | Instruction Manual - Page 153
    is received via the D- STAR received audio may be distorted with the auto detection "ON" setting for FM demodulation. 10 11 D Call sign edit record 12 Selects call sign programming programmed channel. A different 14 channel cannot be selected. : The edited or corrected call sign is pro- 15
  • Icom ID-880H | Instruction Manual - Page 154
    as previous time. (default) • AUTO : After selecting a specific station, the transceiver sets the pre-programmed gateway repeater as RPT2 automatically. D RX call sign display When a call is received, the calling station call sign can be displayed automatically. (default: AUTO) D TX call sign
  • Icom ID-880H | Instruction Manual - Page 155
    mode, no call sign set- ting is necessary. When an EMR communication mode sig- 3 nal is received, the audio (voice) will be heard at the speci- 4 fied level even if the volume setting level is is turned OFF 11 automatically when turning transceiver's power OFF 12 13 14 15 16 17 18 19 137
  • Icom ID-880H | Instruction Manual - Page 156
    -12:00 to +12:00 range in 5 min. steps. (default: 0:00) D GPS TX mode items Sets the transmission of data from a connected GPS receiver ON or OFF. When the position information is received from a connected GPS receiver and "GPS.ATX" (GPS Auto TX Timer) setting (p. 141) is set to a specific time, the
  • Icom ID-880H | Instruction Manual - Page 157
    • "API880,DSTAR " is preset as the default. • The first character blinks. • Push [≈](LOW) to move programmed. r Push [ ](MONI) to program the unproto address and return to the unproto address edit mode. t Push [ ](CS) to return to GPS-A set mode item indication. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
  • Icom ID-880H | Instruction Manual - Page 158
    speed information is additionally transmitted with position data when "CUR.SPD" is selected. Second is transmitted. 140 - GPS-A symbol Selects the desired GPS-A symbol. Available symbols: AMBU is programmed previously. w Rotate [DIAL] to select the 1st character from "\" and "/." e Push [ ](LOW)
  • Icom ID-880H | Instruction Manual - Page 159
    GPS position data. *Only 36 character are available when "CUR.SPD" (COURSE/ SPEED) is selected in DT EXT (data extension). q Push [ ](MONI) to enter programming. w Rotate [DIAL] to select the desired character. • The selected character blinks. • Push [≈](LOW . 12 13 14 15 16 17 18 19 141
  • Icom ID-880H | Instruction Manual - Page 160
    ](MONI). e Rotate [DIAL] to select the desired memory channel, then push [ ](MONI). • Previously programmed DTMF code is displayed if pro- grammed. r Rotate [DIAL] to select the desired code. t Push [ ](LOW) to select the next digit. • Pushing [ ](CS) moves the cursor backward. y Repeat steps r and
  • Icom ID-880H | Instruction Manual - Page 161
    ON continuously, each push of the PTT transmits the previously selected DTMF tone sequence. 2 z Push [FUNC] then [LOW 6(DTMF)] to turn the 3 DTMF DTMF memory encoder ON. • " " appears in place of 100 MHz digit. se- 8 lected DTMF tone sequence. 9 10 11 12 13 14 15 16 17 18 19 143
  • Icom ID-880H | Instruction Manual - Page 162
    LOW 6(DTMF)] to turn the DTMF-S DTMF memory encoder ON. • " " appears in place of 100 MHz digit. x Push [DTMF-S] to turn the DTMF memory di- rect selection ON. • The function indicator (microphone transmits the relative DTMF tone sequence as the manual transmission described as at right. v Push [ 144
  • Icom ID-880H | Instruction Manual - Page 163
    DTMF MEMORY ENCODER 11 DTMF speed The rate at which DTMF values in memory send individual DTMF characters can be set to accommodate operating needs. q Enter "DTMF-S" in the DUP.T menu.
  • Icom ID-880H | Instruction Manual - Page 164
    TSQLS)] : Tone squelch with pocket beep • [SIMP 9(TSQL)] : Tone squelch c When a signal with the correct tone or code is received, the transceiver's mute is released and received audio sound. • Emits beep tones for 30 sec. and blinks " " if pocket beep is selected in step x. v Push [PTT] to
  • Icom ID-880H | Instruction Manual - Page 165
    . r Rotate [DIAL] to select the desired squelch system. Tone squelch reverse DTCS reverse t When a signal with unmatched tone or code is received, the transceiver's mute is released and the received audio sounds. The transceiver mutes the squelch when a signal with the matched tone or code is
  • Icom ID-880H | Instruction Manual - Page 166
    12 TONE SQUELCH AND POCKET BEEP D Setting DTCS code q Enter "CODE" (DTCS code) in the DUP.T menu.
  • Icom ID-880H | Instruction Manual - Page 167
    DTCS polarity setting q Enter "DTCS-P" (DTCS polarity) in the DUP.T menu.
  • Icom ID-880H | Instruction Manual - Page 168
    DTCS code scan 150 y When the CTCSS tone frequency or 3-digit DTCS code is matched, the squelch opens and the tone frequency is temporarily programmed into the selected feature, such as memory or call channel. • The tone scan pauses when a CTCSS tone frequency or 3-digit DTCS code is detected
  • Icom ID-880H | Instruction Manual - Page 169
    code beep " CSQL" and Digital code squelch "CSQL" appears in order. [DIAL] [TONE] t When the received signal includes a matching call sign/ code, the squelch opens and the signal can be heard. • When the call sign squelch Digital code squelch 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 151
  • Icom ID-880H | Instruction Manual - Page 170
    12 TONE SQUELCH AND POCKET BEEP D UR and MY call signs setting q Enter "UR" in call sign screen.
  • Icom ID-880H | Instruction Manual - Page 171
    GPS.SET settings, GPS alarm areas (ALM1, ALM2), Sentence formatter settings, GPS-A set mode settings, Transmit output power level 1 ± Programming are assigned to the [UP]/[DN] keys on the other microphones (HM-103/HM-154) in set mode. 15 • Default setting 16 [UP] : channel up; push and
  • Icom ID-880H | Instruction Manual - Page 172
    power OFF. After waiting a few seconds, turn power ON again. If the problem persists, perform the following procedure. • Partial reset is also available. See right for details. IMPORTANT!: Resetting the CPU CLEARS all programmed contents to the their default settings. q Push and hold [ ] for 1 sec
  • Icom ID-880H | Instruction Manual - Page 173
    OTHER FUNCTIONS 13 Data cloning AT POWER ON D Cloning between transceivers The ID-880H has transceiver-to-transceiver data cloning capability. This function is useful when you want to copy all of the programmed contents from one ID-880H to another. • A optional OPC-474 CLONING CABLE is required.
  • Icom ID-880H | Instruction Manual - Page 174
    The CS-80/880 CLONING SOFTWARE (free download) is also available to clone/edit contents with a PC (for Microsoft® Windows® 2000/XP or Windows Vista®) using ICF format files. To connect the transceiver and a PC, either the optional data communication cable; OPC-1529R or cloning cable; OPC478/478UC is
  • Icom ID-880H | Instruction Manual - Page 175
    OTHER FUNCTIONS 13 Auto power OFF The transceiver can be set to automatically turn OFF after a specified period with a beep when no switch is pushed. 120 min., 90 min., 60 min., 30 min. and OFF can be specified. The specified period is retained even when the transceiver is turned OFF by the auto power
  • Icom ID-880H | Instruction Manual - Page 176
    ±4 kHz. • When NOT using a deviation meter: A receiver or transceiver is needed to monitor the transmission-compare the received audio output level when receiving a TNC modulated signal with high level voice signals using the microphone. Then adjust the TNC modulated signal to a lower level than the
  • Icom ID-880H | Instruction Manual - Page 177
    • Read the instructions supplied with your TNC carefully before attempting packet operation with the transceiver. • Pin t AF OUT is for 1200 bps operation only. many transmissions are failing, re-adjust the modulation level. OTHER FUNCTIONS 13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 159
  • Icom ID-880H | Instruction Manual - Page 178
    and a TNC as illustrated below. TNC side q DATA IN TX AUDIO w GND GND e PTT P r DATA OUT y P SQL RX AUDIO PTT SQL microphone. • When pushing [PTT] during data transmission, data transmission is interrupted and the voice signal takes priority. • Read the instructions supplied with your TNC
  • Icom ID-880H | Instruction Manual - Page 179
    TX audio output level (DATA IN level) from the TNC as TNC output level until the transmit indicator lights continuously. When transmission is not successful even though the TX indicator lights continuously: - Increase the TNC output level. OTHER FUNCTIONS 13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
  • Icom ID-880H | Instruction Manual - Page 180
    13 OTHER FUNCTIONS Weather channel operation D Weather channel selection q Push [M/CALL] several times to select weather channel group. [M/CALL] Weather channel group indicaiton w Rotate [DIAL] to select the desired weather channel. e Push [M/CALL] to select the memory mode, or push [VFO/ MHz]
  • Icom ID-880H | Instruction Manual - Page 181
    than the weather alert frequency, the receiving signal will be interrupted momemtarily appoximately every 5 sec. when the Weather alert function is ON. These interruptions cease when the Weather alert function is turned OFF. OTHER FUNCTIONS 13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 163
  • Icom ID-880H | Instruction Manual - Page 182
    14 MAINTENANCE Troubleshooting If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. PROBLEM POSSIBLE CAUSE SOLUTION REF. Does not turn on. • Power connector has a poor contact. • Polarity of the power connection is reversed.
  • Icom ID-880H | Instruction Manual - Page 183
    too high. eration, the received audio breaks off at the other station. • Select low microphone sensitivity in the FUNC set p. 127 mode. • Turn the ALC function ON in the FUNC set mode. p. 127 The function display shows • The CPU is malfunctioning. erroneous information. • Reset the CPU. p. 154
  • Icom ID-880H | Instruction Manual - Page 184
    • Power supply requirement : 13.8 V DC ±15% • Current drain (at 13.8 V DC: approx.): Transmit at 50 W VHF: 11.5 A* UHF: 12.5 A* * 8.0 A (at 25 W) only for the TPE version Receive standby 0.9 A (simultaneous receive) max. audio 1.2 A • Antenna connector : SO-239 (50 Ω) • Dimensions
  • Icom ID-880H | Instruction Manual - Page 185
    MHz 260-299.995 MHz 300-349.995 MHz 350-399.995 MHz 400-499.995 MHz 500-549.995 MHz 810-879.990 MHz 880-999.990 MHz FM (μV) typical (12dB SINAD) 0.16 0.16 0.56 0.32 0.22 0.22 0.16 0.16 0.45 0.45 AM (μV) typical (10dB S/N) 0.5 0.5 1.8 1 0.79 0.63 0.56 0.56 N/A N/A SPECIFICATIONS
  • Icom ID-880H | Instruction Manual - Page 186
    to connect a regular 8-pin microphone. OPC-1529R DATA COMMUNICATION CABLE (RS-232C type) Allows low-speed data communication in the DV mode and data cloning operation with CS-80/880 (free download software). SP-10 EXTERNAL SPEAKERS For all-round mobile operation. Cable length: 1.5 m; 4.9 ft† MB-120
  • Icom ID-880H | Instruction Manual - Page 187
    STAR TNC 161 Alarm area 1 84 Alarm area 2 85 All reset 154 Antenna connector V Antenna information 1 Antenna installation V Antenna location V Attenuator (AT-ATT 127 Audio filter (AF-FIL 132 Audio microphone 114 Call record channel 44 Call sign edit record (EDIT R 135 Call sign programming
  • Icom ID-880H | Instruction Manual - Page 188
    error 156 Cloning using personal computer 156 Comment (COMMEN 141 Confirming current call sign 43 Confirming the setting (in the DR mode 55 Connecting to a DC power source VI Connecting to a DC power supply VI Connection (GPS receiver 73 Connection for the Low-speed data communication 70
  • Icom ID-880H | Instruction Manual - Page 189
    Function guide indicator 6 Fuse replacement 165 - G - Gateway repeater call sign programming (GW CAL 36, 40 General (MENU screen 116 General (Repeater operation 22 General description 87 GPS alarm setting 81 GPS alarm setting in GPS memory channel 82 GPS auto TX timer (GPS.ATX 142 GPS data
  • Icom ID-880H | Instruction Manual - Page 190
    setting 70 Low-speed data communication operation 70 - M - Main unit 1 Maintenance 164 Manual transmission (DTMF 144 Memory bank link function (B-LINK 124 Memory bank scan 106 Memory bank selection 93 Memory bank setting 92 Memory channel contents 87 Memory channel programming 90 Memory
  • Icom ID-880H | Instruction Manual - Page 191
    94 Programming memory channels XI Programming memory name 94 Programming scan edges via the microphone 104 Programming scan name 94 PTT lock (PTT LK 127 - Q - Quick reference guide I - R - Received call sign 44 Received GPS message indication 76 Receiving 17 Receiving a D-STAR repeater
  • Icom ID-880H | Instruction Manual - Page 192
    78 Saving received position data 78 Scan edges programming 103 SCAN mode items 123 Scan name (SCAN N 132 Scan operation 100 Scan pause timer (PAUSE 109, 123 Scan resume condition 109 Scan resume timer (RESUME 109, 123 Scan start/stop via the microphone 107 Scan stop beep (STOP B 133 Scan
  • Icom ID-880H | Instruction Manual - Page 193
    and pocket beep 146 Transferring bank contents 99 Transmission condition setting (Low-speed data communication)··71 Transmitting 17 Transmitting a DTMF code directly 144 Transmitting a DTMF tone sequence 143 Troubleshooting 164 TSQL frequency (C TONE 121 Tune the frequency IX Tuning step
  • Icom ID-880H | Instruction Manual - Page 194
    MEMO 176
  • Icom ID-880H | Instruction Manual - Page 195
    MEMO 177
  • Icom ID-880H | Instruction Manual - Page 196
    A-6728D-1EX-0a Printed in Japan © 2009 Icom Inc. Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
MODIFICATION OF THIS DEVICE TO RECEIVE CEL-
LULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED
UNDER FCC RULES AND FEDERAL LAW.
INSTRUCTION MANUAL
ID-880H
VHF/UHF DIGITAL TRANSCEIVER