InSinkErator Indulge Contemporary F-GN1100 Owners Manual - Page 4
Installing The Faucet - 1100/2200, Preparation - hot water dispenser
View all InSinkErator Indulge Contemporary F-GN1100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
START HERE proper installation should take ABOUT 2-4 hours 1 aPreparation Required minimum from center of hole to wall F-HC1100 25⁄8" F-GN1100 31⁄4" F-HC2200 27⁄8" F-GN2200 31⁄2" F-HC2215 27⁄8" F-GN2215 31⁄2" F-HC3300 21⁄2" F-H3300 21⁄2" Maximum counter thickness is 3". Identify locations for the dispenser faucet, tank and filter. C heck to make sure there is proper clearance for dispenser handles to be fully opened. C heck to make sure counter is 3" thick or less. M ake sure there is a grounded electrical outlet under the sink. The wall outlet for your dispenser must have power supplied to it continuously and must be fused. It should not be controlled by the same wall switch that operates your disposer, unless using an InSinkErator SinkTop SwitchTM. b If you have to drill through sink or countertop, you may need to rent or purchase the appropriate tools. Turn off water supply. If using the sink sprayer hose hole, remove nut that connects sprayer hose at bottom of faucet. Using adjustable wrench, remove nut connecting sprayer washer flange in sprayer hole. Plug hose opening with either a 1/8" plug or a 1/4" cap (not supplied). c Required Hole Size F-HC1100 13⁄8" - 11⁄2" F-GN1100 11⁄4" - 11⁄2" F-HC2200 13⁄8" - 11⁄2" F-GN2200 11⁄4" - 11⁄2" F-HC2215 13⁄8" - 11⁄2" F-GN2215 11⁄4" - 11⁄2" F-HC3300 13⁄8" - 11⁄2" F-H3300 13⁄8" - 11⁄2" Consult a professional before drilling into a surface other than stainless steel. What if you don't have a sprayer hole or don't want to use it? Many homeowners replace the soap dispenser in their sink with an instant hot water dispenser. If drilling a hole into a stainless steel sink or counter top, you can cut a mounting hole for the dispenser with a hole saw for stainless steel, or you can use a hole punch. 6 2 Installing the fauceT - 1100/2200 a U npack dispenser components. O n a firm, flat surface, carefully straighten the copper tubing. Property Damage: Do not pinch or break copper tubing. Do not distort the last 1 inch of tubing. b E nsure that the black O-ring is1 properly seated in the base of the dispenser head (the groove on the underside of the dispenser). Make sure to use rubber O-ring to ensure proper seal. c P F eed tubes down through the hole in the sink or countertop until the base is at rest on the sink or countertop surface. To ease feeding of tubes through hole, first insert blue tube with quick-connect attachment and then insert the remaining tubes. 1 2 d Semi-circular mounting plate3should encircle all descending tubes and extend beyond sink hole when tight. An assistant may be needed to hold the dispenser head in place while securing the dispenser. F rom under the sink, place the semi-circular mounting plate onto the threaded stud. P lace hex nut onto the threaded stud. Ensure faucet head is at desired angle. I nsert screwdriver into hole on side of hex tool (creating a "T"), and use tool to tighten nut and secure faucet. 1 7