Invacare TRSX5 Owners Manual - Page 45

Adjusting the Seat Width

Get Invacare TRSX5 PDF manuals and user guides View all Invacare TRSX5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

7 SEAT AND BACK 7.3 Adjusting the Seat Width  For this procedure, refer to FIGURE 5 on page 46, FIGURE 6 on page 47, and FIGURE 7 on page 48. When adjusting the seat width of the wheelchair, the back and seat upholstery MUST be changed. If applicable, the headrest pillow and headrest upholstery MUST be changed as well. 1. Remove the existing back and seat upholstery from the wheelchair. Refer to Replacing Back Upholstery on page 43 and Replacing Seat Upholstery on page 43. 2. Remove the four button screws and locknuts that secure the two pivot links to the wheelchair frame and crossbraces. 3. Remove the two button screws, locknuts and crossbrace saddle that secures the bottom of the crossbrace to the wheelchair frame. Repeat for other crossbrace. 4. Remove the hex screw, coved washers, washers and locknut that secure the two crossbraces together. See Detail "B".  Note the orientation of the coved washers, washers and locknut for assembling the new crossbraces. See Detail "B". 5. Assemble the two new crossbraces together with the existing hex screw, coved washers, washers and locknut. Securely tighten. Refer to Detail "B" for hardware orientation. 6. Determine the correct pivot link and mounting hole to use with the desired seat width. See chart below. 7. Secure the pivot links to the crossbraces and wheelchair frame with the four button screws and locknuts. Securely tighten.  Position crossbrace saddle on wheelchair frame using the washer on the underside of the wheelchair frame as a reference. See Detail "A" for proper positioning of the crossbrace saddle. 8. Reinstall the two button screws, locknuts and crossbrace saddle that secures the bottom of the new crossbrace to the wheelchair frame. Refer to Detail "B" for hardware orientation. Repeat for opposite crossbrace. Securely tighten. 9. Install the new back and seat upholstery onto the wheelchair. Refer to Replacing Back Upholstery on page 43 and Replacing Seat Upholstery on page 43. Part No. 1110550 45 Invacare® Tracer® SX5 Wheelchair

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
7
SEAT AND BACK
Part No. 1110550
45
Invacare
®
Tracer
®
SX5 Wheelchair
7.3
Adjusting the Seat Width
1.
Remove the existing back and seat upholstery from the wheelchair. Refer to Replacing Back Upholstery
on page 43 and Replacing Seat Upholstery
on page 43.
2.
Remove the four button screws and locknuts that secure the two pivot links to the wheelchair frame and crossbraces.
3.
Remove the two button screws, locknuts and crossbrace saddle that secures the bottom of the crossbrace to the wheelchair frame. Repeat for
other crossbrace.
4.
Remove the hex screw, coved washers, washers and locknut that secure the two crossbraces together. See Detail "B".
5.
Assemble the two new crossbraces together with the existing hex screw, coved washers, washers and locknut. Securely tighten. Refer to Detail "B"
for hardware orientation.
6.
Determine the correct pivot link and mounting hole to use with the desired seat width. See chart below.
7.
Secure the pivot links to the crossbraces and wheelchair frame with the four button screws and locknuts. Securely tighten.
8.
Reinstall the two button screws, locknuts and crossbrace saddle that secures the bottom of the new crossbrace to the wheelchair frame. Refer
to Detail "B" for hardware orientation. Repeat for opposite crossbrace. Securely tighten.
9.
Install the new back and seat upholstery onto the wheelchair. Refer to Replacing Back Upholstery
on page 43 and Replacing Seat Upholstery
on
page 43.
For this procedure, refer to FIGURE 5 on page 46, FIGURE 6 on page 47, and FIGURE 7 on page 48.
When adjusting the seat width of the wheelchair, the back and seat upholstery MUST be changed. If applicable, the headrest
pillow and headrest upholstery MUST be changed as well.
Note the orientation of the coved washers, washers and locknut for assembling the new crossbraces. See Detail "B".
Position crossbrace saddle on wheelchair frame using the washer on the underside of the wheelchair frame as a reference.
See Detail "A" for proper positioning of the crossbrace saddle.