JVC GR D90U Instructions - Page 36

Audio Dubbing The audio track can be customized only when recorded in the 12-bit mode (੬ pg. 28). NOTES: ● Audio Dubbing is not possible on a tape recorded in 16-bit audio, on a tape recorded in the LP mode or on a blank portion of a tape. ● To perform Audio Dubbing while watching on the television, make connections (੬ pg. 16). 1 Play back the tape to locate the point where editing will start, then press PAUSE (6) Y. 2 While holding A.DUB (e) k on the remote control, press PAUSE (6) Y. "6e" E and "MIC" (GR-D90/D70 only) appear. 3 Press PLAY (4) j, then begin "narrating". Speak into the microphone. • To pause dubbing, press PAUSE (6) Y. 4 To end Audio Dubbing, press PAUSE (6) Y, then STOP (5) P. To hear the dubbed sound during playback set "12BIT MODE" to "SOUND 2" or "MIX" in the Menu Screen (੬ pg. 32). NOTES: ● Sound is not heard from the speaker during Audio Dubbing. ● When editing onto a tape that was recorded at 12-bit, the old and new soundtracks are recorded separately. ● If you dub onto a blank space on the tape, the sound may be disrupted. Make sure you only edit recorded areas. ● If feedback or howling occurs during TV playback, move the camcorder's microphone away from the TV, or turn down the TV's volume. ● If you change from 12-bit to 16-bit in mid-recording and then use the tape for Audio Dubbing, it is not effective from the point where 16-bit recording began. ● During Audio Dubbing, when the tape moves to scenes recorded in the LP mode, scenes recorded in 16-bit audio or a blank portion, Audio Dubbing stops (੬ pg. 50). ● To perform Audio Dubbing with a video unit connected to the camcorder's AV connector, first set "S/AV INPUT" to "ON" in the Menu Screen (੬ pg. 31). "AUX" appears instead of "MIC". Insert Editing You can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in and outpoints. The original audio remains unchanged. NOTES: ● Before performing the following steps, make sure that "TIME CODE" is set to "ON" in the Menu Screen (੬ pg. 31, 32). ● Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape. ● To perform Insert Editing while watching in the television, make connections (੬ pg. 16). 1 Play back the tape, locate the Edit-Out point and press PAUSE (6) Y. Confirm the time code at this point (੬ pg. 31, 32). 2 Press REW (2) I until the Edit-In point is located, then press PAUSE (6) Y. 3 Press and hold INSERT (w) O on the remote control, then press PAUSE (6) Y. "6w" 8 and the Time Code (min.:sec.) appear and the camcorder enters Insert-Pause mode. 4 Press START/STOP s to begin editing. • Confirm the insert at the time code you checked in step 1. • To pause editing, press START/STOP s. Press it again to resume editing. 5 To end Insert Editing, press START/STOP s, then STOP (5) P. NOTES: ● Program AE with special effects (੬ pg. 23) can be used to spice up the scenes being edited during Insert Editing. ● During Insert Editing, the date and time information changes. ● If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas. ● During Insert Editing, when the tape moves to scenes recorded in the LP mode or a blank portion, Insert Edting stops (੬ pg. 50). E Stereo microphone R T UY I O P a 6 9 0 2 4 3 w 5 e T W s d f g hj k l ; A EN USING THE REMOTE CONTROL UNIT 36 (GR-D90 and GR-D70 only)