Jensen PCD120U Owners Manual - Page 4

Installation Using a Kit, ISO Installation, Removing the Radio

Get Jensen PCD120U - Phase Linear Radio PDF manuals and user guides View all Jensen PCD120U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

INSTALLATION INSTRUCTIONS Installation Using a Kit 1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit. 2. Wire and test the radio as described in step 4 of "Installation Using Mounting Sleeve" on page 3. 3. Install the radio mounting plate assembly to the sub-dashboard according to the instructions of the installation kit. 4. Attach the support strap to the radio and dashboard as described in step 6 of "Installation Using Mounting Sleeve" on page 3. 5. Replace the dashboard trim panel. ISO Installation This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of installation. 1. Remove the existing factory radio from the dashboard or center console mounting. ISO INSTALLATION Save all hardware and brackets as they will be used to mount the new radio. 2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame. 3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio. CAUTION: Do not exceed M5 X 6 MM screw size. Longer screws may touch and damage components inside the chassis. 4. Wire the new radio to the vehicle as described in step 4 of "Installation Using Mounting Sleeve" on page 3. 5. Mount the new radio assembly to the dashboard or center console using the 4 PCD120U reverse procedure in step 1 of "Installation Using Mounting Sleeve" on page 3. Removing the Radio To remove the radio after installation, remove the trim ring by lifting in the center and pulling it off from either side. Insert the removal keys straight back until they lock, and pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. REMOVING THE RADIO

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
PCD120U
4
INSTALLATION INSTRUCTIONS
Installation Using a Kit
1.
If your vehicle requires the use of an
installation kit to mount this radio, follow
the instructions included with the
installation kit to attach the radio to the
mounting plate supplied with the kit.
2.
Wire and test the radio as described in
step 4 of
“Installation Using Mounting
Sleeve” on page 3.
3.
Install the radio mounting plate assembly
to the sub-dashboard according to the
instructions of the installation kit.
4.
Attach the support strap to the radio and
dashboard as described in step 6 of
“Installation Using Mounting Sleeve” on
page 3.
5.
Replace the dashboard trim panel.
ISO Installation
This unit has threaded holes in the chassis side
panels which may be used with the original
factory mounting brackets of some Toyota,
Nissan, Mitsubishi, Isuzu, Hyundai and Honda
vehicles to mount the radio to the dashboard.
Please consult with your local car stereo
specialty shop for assistance on this type of
installation.
1.
Remove the existing factory radio from the
dashboard or center console mounting.
Save all hardware and brackets as they
will be used to mount the new radio.
2.
Carefully un-snap the plastic frame from
the front of the new radio chassis. Remove
and discard the frame.
3.
Remove the factory mounting brackets
and hardware from the existing radio and
attach them to the new radio.
CAUTION: Do not exceed M5 X 6 MM screw
size. Longer screws may touch and damage
components inside the chassis.
4.
Wire the new radio to the vehicle as
described in step 4 of “Installation Using
Mounting Sleeve” on page 3.
5.
Mount the new radio assembly to the
dashboard or center console using the
reverse procedure in step 1 of “Installation
Using Mounting Sleeve” on page 3.
Removing the Radio
To remove the radio after installation, remove
the trim ring by lifting in the center and pulling it
off from either side. Insert the removal keys
straight back until they lock, and pull the radio
out. If removal keys are inserted at an angle,
they will not lock properly to release the unit.
ISO INSTALLATION
REMOVING THE RADIO