Kenmore 3243 Installation Instructions - Page 6

Outlet, Location, Cooktop, Installation, Clamp, Information, Provide, an Adequate, Gas Supply, LP/

Page 6 highlights

Wail Outlet Location _12" 4 10" Recommended 12OV grounded on rear wall. area for outlet 22" : NOTE: If an outlet is not available, [ have one installed by _ a qualified technician. ½ OF UNIT Figure 3 Cooktop Installation 1. Visually inspect the cooktop for damage. 2. Set the cooktop into the countertop cutout. NOTE: Do not use caulking compound; cooktop should be removable for service when needed. Clamp Down Information Once the cooktop is installed in the counter opening, you must (.lamp the unit down as shown. Counte_op To clamp down, insert an angle bracket into the slot on each side of the unit as shown.Run thumb screw up through tile bracket, up against the bottom of the counter. Tighten until the unit draws down and is secure. Provide an Adequate Gas Supply This (ooktop is designed to operate on natural gas at 4" of manifold pressure only. A pressure regulator is connected in series with the manifold on the cooktop and must remain in series with tile supply line. For proper operation, the maximum inlet pressure to the regulator must be no more than 14" of water column (W.C.) pressure. For checking the regulator, the inlet pressure must be at least I" (or 2.5 kPa) greater than the regulator manifold pressure setting. The regulator is set for 4" of manifold pressure, the inlet pressure must be at least 5". Tile gas supply line to tile range should be 1/2" or 3/4" pipe. LP/Propane Gas Conversion This appliance can be used with Natural gas or LP/ Propane gas. It is shipped from the factory for use with natural gas. A kit for converting to LP gas is supplied with your cooktop. The kit is marked "FOR LP/PROPANEGAS CONVERSION". The conversion must be performed by a qualified service technician in accordance with the kit instructions and all local codes and requirements. Failure to follow instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for the conversion. Failure to make the appropriate conversion can result in serious personal injury and property damage. Figure 4 Thumb Screw

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

Wail
Outlet
Location
_12"
4
10"
Recommended
area for
12OV grounded
outlet
on rear wall.
22"
: NOTE:
If an outlet
is not available,
[
have one
installed
by
_ a qualified
technician.
½
OF
UNIT
Figure
3
Cooktop
Installation
1. Visually inspect the cooktop for damage.
2. Set the cooktop
into the countertop
cutout.
NOTE: Do not use caulking compound;
cooktop
should
be removable
for service when needed.
Clamp
Down
Information
Once the cooktop
is installed in the counter opening,
you
must (.lamp the unit down as shown.
Counte_op
Thumb
Screw
Figure
4
To clamp down,
insert an angle bracket into the slot on
each side of the unit as shown.Run
thumb
screw up
through
tile
bracket, up against the bottom
of the
counter. Tighten
until the unit draws down and is secure.
Provide
an Adequate
Gas Supply
This (ooktop
is designed to operate on natural gas at 4"
of manifold
pressure only.
A pressure regulator
is connected
in series with the
manifold
on the cooktop
and must remain in series with
tile supply line.
For proper
operation,
the maximum
inlet pressure to
the regulator
must be no more than 14" of water
column
(W.C.) pressure.
For checking the regulator,
the inlet pressure must be at
least I"
(or 2.5 kPa) greater than the regulator
manifold
pressure setting. The regulator
is set for 4"
of manifold
pressure, the inlet
pressure must be at least 5".
Tile gas supply line to tile range should be 1/2" or 3/4"
pipe.
LP/Propane
Gas Conversion
This appliance
can be used with
Natural gas or LP/
Propane gas. It is shipped from the factory
for use with
natural gas.
A kit for converting
to LP gas is supplied with
your
cooktop.
The kit is marked
"FOR LP/PROPANEGAS
CONVERSION".
The conversion must be performed
by a qualified
service
technician
in accordance with
the kit instructions
and all
local codes and requirements.
Failure to follow
instructions
could result in serious injury or property
damage. The qualified
agency performing
this work
assumes responsibility for the conversion.
Failure to make the appropriate
conversion can result in serious personal injury and
property
damage.