KitchenAid KUID508HPS Installation Instructions - Page 17

Deep Clean, Interior Components

Get KitchenAid KUID508HPS PDF manuals and user guides View all KitchenAid KUID508HPS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Deep Clean Interior Components 1. Unplug ice maker or disconnect power. 2. Open the storage bin door and remove any ice that is in the bin. 3. Remove the drain cap from the water pan and drain thoroughly. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice. 4. Pull out on the bottom of the cutter grid cover until the snaps release to remove. NOTE: On some models, remove the screw from the cutter grid cover. 5. Unplug the wiring harness from the left side of the cutter grid. A B A. Cutter grid cover B. Screw (on some models) 8. Remove the mounting screw that holds the water pan in place. Pull out on the front of the water pan. 9. Disconnect the pump bracket from the water pan and unplug the water pan drain pump. A B C D A. Water pan B. Water pan screw C. Drain cap D. Drain pump cover 10. Remove, clean and replace the ice scoop holder and ice scoop. NOTE: On some models, the ice scoop holder is located in the upper left of the unit, and on other models, the ice scoop holder is located in the lower left of the unit. On Some Models ■■ Remove the holder by removing the 2 screws. ■■ Wash the ice scoop holder and ice scoop along with the other interior components using the following instructions. ■■ Replace the ice scoop holder by replacing the screws. A B A A. Cutter grid cover 6. Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid. 7. Remove the right-hand and left-hand screws. Lift the cutter grid up and out. NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid. D A B E C F A. Cutter grid harness B. Screw C. Cutter grid D. Ice level sensor harness E. Plastic spacer F. Screw A. Screw B. Ice scoop holder On Some Models ■■ After removing the ice scoop, remove the holder by removing the 2 screws. NOTE: On some models, remove the holder by lifting up on the ice scoop holder and then out. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
17
Deep Clean
Interior Components
1.
Unplug ice maker or disconnect power.
2.
Open the storage bin door and remove any ice that is in the
bin.
3.
Remove the drain cap
from the water pan and drain
thoroughly. Replace the drain cap securely on the water pan.
If the drain cap is loose, water will empty from the water pan,
and you will have either thin ice or no ice.
4.
Pull out on the bottom of the cutter grid cover until the snaps
release to remove.
NOTE:
On some models, remove the screw from the cutter
grid cover.
5.
Unplug the wiring harness from the left side of the cutter grid.
6.
Unplug the ice level sensor from the right side of the cutter
grid. Pull the ice level sensor down and forward away from the
cutter grid.
7.
Remove the right-hand and left-hand screws. Lift the cutter
grid up and out.
NOTE:
Make sure the plastic spacer from the right-hand side
of the cutter grid bracket stays with the cutter grid.
8.
Remove the mounting screw that holds the water pan in
place. Pull out on the front of the water pan.
9.
Disconnect the pump bracket from the water pan and unplug
the water pan drain pump.
10.
Remove, clean and replace the ice scoop holder and ice
scoop.
NOTE:
On some models, the ice scoop holder is located in
the upper left of the unit, and on other models, the ice scoop
holder is located in the lower left of the unit.
On Some Models
■
Remove the holder by removing the 2 screws.
■
Wash the ice scoop holder and ice scoop along with the
other interior components using the following instructions.
■
Replace the ice scoop holder by replacing the screws.
On Some Models
■
After removing the ice scoop, remove the holder by
removing the 2 screws.
NOTE:
On some models, remove the holder by lifting up
on the ice scoop holder and then out.
A
B
A. Cutter grid cover
B. Screw (on some models)
A
A. Cutter grid cover
A
B
C
D
E
F
A. Cutter grid harness
B. Screw
C. Cutter grid
D. Ice level sensor harness
E. Plastic spacer
F. Screw
A
B
C
D
A. Water pan
B. Water pan screw
C. Drain cap
D. Drain pump cover
B
A
A. Screw
B. Ice scoop holder