Home » Konica Minolta Manuals » Printers » Konica Minolta bizhub PRESS C71hc » Manual Viewer

Konica Minolta bizhub PRESS C71hc bizhub PRESS C1070/C1070P/C1060/C71hc/bizhub - Page 60

Maintaining the Finishing Quality, 5.1 Both Sides Adjustment, Adjustment flow

View all Konica Minolta bizhub PRESS C71hc manuals

Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

5.1 Both Sides Adjustment 5 Maintaining the Finishing Quality 5.1 Both Sides Adjustment Both Sides Adjustment When performing the duplex printing, you can adjust a misalignment between the front and back sides to align the printing positions on the front and back sides. This task is referred to as Both Sides Adjustment. A heat impact of the fixing unit may cause a slight enlargement or reduction of paper during printing. The impact level varies depending on the type or weight of paper, therefore, if you have changed paper to be loaded into a tray, be sure to carry out the Both Sides Adjustment. Tips Two methods are available to carry out the Both Sides Adjustment: entering from [Paper Setting] and from [Both Sides] on the [MACHINE] screen. This guide describes how to enter from [Paper Setting] for adjustment. Reference For information about how to enter from [Both Sides], refer to the HTML User's Guide. Adjustment flow Follow the procedure below to proceed the Both Sides Adjustment. " Check the reference position of the print side To judge whether a print position is misaligned, the required reference position adjustment must be completed on this machine. Before starting the Both Sides Adjustment, check the adjustment value of the reference position. If necessary, adjust it. There are the following adjustment items to be checked. To check them, on the [MACHINE] screen, select [Adjustment] - [Machine Adjustment] - [Printer Adjustment]. - [01 Restart Timing Adjustment] - [02 Centering Adjustment] - [03 FD-Mag. Adjustment] - [04 CD-Mag. Adjustment] First adjust the front side in the order of 03 -> 04 -> 01 -> 02, then adjust the back side in the same order. For information about how to check or readjust the adjustment value, refer to the HTML User's Guide. # Making the Both Sides Adjustment for each tray The following adjustment methods are available. - Scan Measurement Adjustment: the method used for adjusting the zoom ratio and printing position of the back side based on those of the front side to match the appearance of the front and back sides. Both Sides Adjustment is automatically carried out using the scanner function of this machine. (page 5-2) (bizhub PRESS C1070P/bizhub PRESS C71hc does not support the [Scan Meas.] adjustment.) - Gap Adjustment: the method used for aligning both sides with correction of the back side magnification and print position based on the front side ones (page 5-10). - Chart Adjustment: the method used for aligning both sides with correction of the magnification and print position of both front and back side (page 5-15). - Zoom and Image Shift Adjustment: the method used for fine adjustment after Scan Measurement Adjustment, Gap Adjustment or Chart Adjustment, or the method used when the amount of misalignment between both sides is figured out (page 5-22). 5-1

Section	Page
Intended use of this machine	3
Intended use	3
Impermissible operating conditions	3
Exclusion of liability	3
Target groups	3
Configuration and Usage of this Guide	4
HTML User's Guide operating environment	5
Supported Operating Systems/Browsers	5
Display resolution	5
How to display the top page of the HTML User's Guide	5
In a Windows environment	5
In a Macintosh environment	5
Conventions used in this guide	6
Make a Note about This Machine Information	7
Checking the mounted optional devices	7
Checking network information	8
Printing out the Configuration Page Print	8
Contents	9
1 Before Getting Started	13
1.1 Turning the Power ON/OFF	13
Power supply	13
Turning the power on	13
Turning the power off (Image Controller IC-415)	15
Turning off the power (Image Controller IC-308)	18
Power-saving function	20
1.2 Available Operations in this Machine	21
Major functions of this machine	21
Print functions	21
Copy functions	21
Scan functions	22
Hold function of print jobs using the HDD	22
Device control function (WebTools)	22
Application functions	23
Fiery Command WorkStation	23
Printer Delete Utility	24
Fiery Remote Scan	25
Fiery Hot Folders	25
2 Let's Make Prints	26
2.1 Printing Flow	26
Step 1: Prepare the printer driver and applications	26
Step 2: Load paper into a tray	26
Step 3: Configure information of the paper loaded into a tray in this machine	27
Step 4: Use the printer driver to print data	27
Step 5: Check the finishing	28
3 Installing Software	29
3.1 Installing the Printer Driver	29
Operating environment	29
In a Windows environment	29
In a Macintosh environment	29
Characteristics of printer driver	29
In a Windows environment	30
Installation	30
Default setting	35
In a Macintosh environment	36
Installation	36
Default setting	39
3.2 Installing Applications	41
Operating environment	41
Fiery Utility	41
Fiery Utility setup	41
Function overview	41
In a Windows environment	42
Installation	42
In a Macintosh environment	44
Installation	44
Starting applications	45
Starting Fiery Command WorkStation	45
Starting Fiery Remote Scan	47
Starting Fiery Hot Folders	47
4 Basic Operations	48
4.1 Loading Paper	48
Loading paper into the main body tray	48
Loading paper into the Paper Feeder Unit PF-602m	50
Loading Paper in Post Inserter of Folding Unit FD-503	51
4.2 Paper Setting	52
Specifying paper information for a tray	52
4.3 Printer Driver Setting	57
Printer driver functions	57
[Color mode]: Select an output color	57
[Color mode]: Basic Settings	58
[Color mode]: Expert Settings	59
5 Maintaining the Finishing Quality	60
5.1 Both Sides Adjustment	60
Both Sides Adjustment	60
Adjustment flow	60
Making the Both Sides Adjustment for each tray	61
Scan Measurement Adjustment	61
Gap Adjustment	69
Chart Adjustment	74
Zoom and Image Shift Adjustment	81
5.2 Image Quality Adjustment	84
Image Quality adjustment	84
To manage the daily image quality	84
To specify the reference image quality	84
Daily image quality management (Calibration)	85
Calibration timing	86
Maximum Density Auto Adjustment (RU)	88
Color Density Control	90
Auto setting of Color Density Control	90
Manual setting of Color Density Manual Control	93
Executing calibration using the image controller	95
Specifying the reference image quality	98
5.3 Adjusting the Finisher and Saddle Stitcher	99
Opening the screen to be adjusted	99
Adjustable settings	100
6 Troubleshooting	102
6.1 Replenish and Replace Consumables	102
Replacing a toner bottle	102
Replacing a staple cartridge	104
Replacing a waste toner box	106
6.2 Clearing Paper Jams	108
How to view the animation guide	108
[JAM Position] screen	108
Illustration screen for Jam handling	109
6.3 If the Specified Paper is not Found	111
6.4 If an Error has been Displayed during Scanning	113
HDD space insufficiency	113
6.5 Hue Adjustment	114
When calibration is executed for daily management	114
When calibration is not executed	114
6.6 Image Position Adjustment	115
7 Appendix	116
7.1 Good Use of the HTML User's Guide	116
(1) Let's master the search function!	116
(2) Confirm the setting required for the target finishing in an operation example!	116
7.2 Name of each Component	117
External components	117
Internal components	119
Control Panel Layout	121
7.3 Convenient Use of Scan Function (Scan to SMB)	123
Step 1: Prepare the destination computer	123
In a Windows environment	123
In a Macintosh environment	125
Step 2: Connect this machine to the network	125
Step 3: Prepare the operating environment for SMB transmission	125
Step 4: Configure settings according to your environment	126
Step 5: Send scan data to a public folder	126
7.4 Major Specifications	127
Machine	127
Feeding-related optional devices	128
Paper Feeder Unit PF-602m	128
Paper Feeder Unit PF-707	129
Large Capacity Unit LU-202	130
Multi Bypass Tray MB-506	131
Post Inserter (Folding Unit FD-503)	132
Post Inserter PI-502	133
Output-related optional devices	134
Relay Unit RU-509	134
Relay Unit RU-510	134
Relay Unit RU-516	135
Relay Unit RU-517	135
Folding Unit FD-503	135
Large Capacity Stacker LS-505	137
Large Capacity Stacker LS-506	138
Saddle Stitcher SD-506	139
Perfect Binder PB-503	140
Finisher FS-531	141
Finisher FS-532	143
Finisher FS-612	146
Multi Puncher GP-501	149
Auto Ring Binder GP-502	150
Banner Tray Unit MK-740	151
Electronic optional devices	152
Image Controller IC-602	152
Image Controller IC-415	152
Image Controller IC-308	152
Authentication Unit AU-201	152
Authentication Unit AU-201S	152
Original-related optional devices	153
Reverse Automatic Document Feeder DF-626	153
7.5 Weight for each size and copying speed	154
Weight for each size	154
Copying speed	154

Match case Limit results 1 per page

5-1

5.1

Both Sides Adjustment

Maintaining the Finishing Quality

5.1

Both Sides Adjustment

When performing the duplex printing, you can adjust a misalignment between the front and back sides to align the

printing positions on the front and back sides. This task is referred to as Both Sides Adjustment.

A heat impact of the

fixing unit

may cause a slight enlargement or reduction of paper during printing. The impact level

varies depending on the type or weight of paper, therefore, if you have changed paper to be loaded into a tray, be sure

to carry out the Both Sides Adjustment.

Tips

Two methods are available to carry out the Both Sides Adjustment: entering from [Paper Setting] and from [Both Sides]

on the [MACHINE] screen. This guide describes how to enter from [Paper Setting] for adjustment.

Reference

For information about how to enter from [Both Sides], refer to the

HTML User's Guide

Adjustment flow

Follow the procedure below to proceed the Both Sides Adjustment.

Check the reference position of the print side

To judge whether a print position is misaligned, the required reference position adjustment must be

completed on this machine.

Before starting the Both Sides Adjustment, check the adjustment value of the reference position. If

necessary, adjust it.

There are the following adjustment items to be checked. To check them, on the [MACHINE] screen, select

[Adjustment] - [Machine Adjustment] - [Printer Adjustment].

[01 Restart Timing Adjustment]

[02 Centering Adjustment]

[03 FD-Mag. Adjustment]

[04 CD-Mag. Adjustment]

First adjust the front side in the order of 03 -> 04 -> 01 -> 02, then adjust the back side in the same order.

For information about how to check or readjust the adjustment value, refer to the

HTML User's Guide

Making the Both Sides Adjustment for each tray

The following adjustment methods are available.

Scan Measurement Adjustment: the method used for adjusting the zoom ratio and printing position

of the back side based on those of the front side to match the appearance of the front and back

sides. Both Sides Adjustment is automatically carried out using the scanner function of this machine.

(page 5-2)

(

bizhub PRESS C1070P

bizhub PRESS C71hc

does not support the [Scan Meas.] adjustment.)

Gap Adjustment: the method used for aligning both sides with correction of the back side

magnification and print position based on the front side ones (page 5-10).

Chart Adjustment: the method used for aligning both sides with correction of the magnification and

print position of both front and back side (page 5-15).

Zoom and Image Shift Adjustment: the method used for fine adjustment after Scan Measurement

Adjustment, Gap Adjustment or Chart Adjustment, or the method used when the amount of

misalignment between both sides is figured out (page 5-22).